Keysight Technologies N9010A Series Installation Note Download Page 14

Page: 14 / 63

Installation Note N9010-90054

Installation Procedure

Analyzer Disassembly

Standard Instrument (Benchtop Configuration)

Disconnect the instrument from ac power.

Refer to

Figure 3

. Using the T-20 driver, remove the four screws (two on each side)

(1)

that

attach the handle strap

(2)

on each side of the instrument.

Using the T-20 driver, remove the four screws (including washers)

(3)

that hold the rear feet

(4)

in place.

Pull the instrument cover

(5)

off towards the rear of the instrument.

If the instrument is placed on its face during any of the following procedures, be sure to use a soft

surface or soft cloth to avoid damage to the front panel, keys, or input connector.

If the analyzer has Option PRC, Portable Configuration, refer to the

“Portable Instrument (Option

PRC)”

section on

page 16

to remove the outer case.

Make sure any adapters on the front panel are removed.

Summary of Contents for N9010A Series
































































Search results

Summary of Contents for N9010A Series

Reviews:

Related manuals for N9010A Series

Brands by name

Popular brands

Keysight Technologies N9010A Series, Installation Note

Search results

Summary of Contents for N9010A Series

Reviews:

Related manuals for N9010A Series

Brands by name

Popular brands