Keysight Technologies N9010A Series Installation Note Download Page 9

Page: 9 / 63

Installation Note N9010-90054

Installation Procedure

Refer to the data in

step 3

above. If the analyzer has N90x0A-503, N9010A-532, or

N9010A-544

do not proceed

with the installation of this kit. This kit can only be installed in

analyzers with frequency range options 507, 508, 513, and 526.

Refer to the data in

step 2

above. If the analyzer is an N9010A and the serial number is

≥

MY/SG/US56480000

do not proceed

with the installation of this kit, This kit is only for older

N9010A and N9020A analyzers.

Refer to the data in

step 2

above. If the analyzer is an N9020A and the serial number is

≥

MY/SG/US52330000

do not proceed

with the installation of this kit, This kit is only for older

N9010A and N9020A analyzers.

Refer to the data in

step 2

above. If the Instrument S/W Revision is earlier than A.10.05, you

must upgrade the instrument software. The hardware and licenses being added with this

upgrade are only supported by software revisions A.10.05 and later.
Even if the Instrument S/W Revision is A.10.05 or later, we recommend upgrading to the latest

software revision to ensure that you get the benefit of any defect fixes that have been made

since A.10.05.
The latest instrument software can be downloaded from the following web site:

http://www.keysight.com/find/xseries_software

10.

Refer to the data in

step 4

above. If the Front End has a Hw Id of 70, it already has the 150 MHz

wide 1st IF bandpass filter and you do not need to perform the Replace A13A1 Bandpass Filter

procedure.

11.

Refer to the data in

step 3

and

step 4

above. If the analyzer has N90x0A-CR3 and/or

N90x0A-CRP installed, verify that it also has a Front End Controller with Hw Id of 41 or 75. If

the Front End Controller has a Hw ID of 41 or 75, you do not need to perform the Replace Front

End Controller procedure.

Summary of Contents for N9010A Series
































































Search results

Summary of Contents for N9010A Series

Reviews:

Related manuals for N9010A Series

Brands by name

Popular brands

Keysight Technologies N9010A Series, Installation Note

Search results

Summary of Contents for N9010A Series

Reviews:

Related manuals for N9010A Series

Brands by name

Popular brands