Keysight Technologies N9010A Series Installation Note Download Page 11

Page: 11 / 63

Installation Note N9010-90054

Installation Procedure

Licensing the New Options

License Installation Procedure over USB

Locate the Option Upgrade Entitlement Certificate (5964-5178) from the kit.

Redeem the Option Upgrade Entitlement Certificate by following the instructions on the

Certificate.

After redeeming your Option Upgrade Entitlement Certificate you will receive an email with an

attached License File.

Locate a USB storage device. Perform a virus scan on this device before use.

Save the License File to the root directory of the USB Storage Device.

Connect the USB Storage Device to one of the analyzer’s USB ports. Connect a mouse to

another USB port. Windows will detect the new hardware and may display the configuration

menu shown in

Figure 1

. This menu may be configured according to your preferences.

Figure 1

USB Storage Device Configuration Menu

Summary of Contents for N9010A Series
































































Search results

Summary of Contents for N9010A Series

Reviews:

Related manuals for N9010A Series

Brands by name

Popular brands

Keysight Technologies N9010A Series, Installation Note

Search results

Summary of Contents for N9010A Series

Reviews:

Related manuals for N9010A Series

Brands by name

Popular brands