Keysight Technologies N5290A Installation Manual Download Page 23

Page: 23 / 96

Keysight N5290/1A Service Guide 1-17

Safety and Regulatory Information
Site Preparation

Site Preparation

Install the instrument so that the detachable power cord is readily identifiable

and is easily reached by the operator. An externally installed switch or circuit

breaker (which is readily identifiable and is easily reached by the operator)

should be used as the disconnecting device.The detachable power cord can

also be used to disconnect the mains circuits from the mains supply before

other parts of the instrument. The front panel switch is only a standby switch

and is not a LINE switch.

Power Requirements

Before installing the system, be sure that the required ac power is available at

all necessary locations.

— Three-wire power cables (which provide a safety ground) must be used with

all instruments.

— Air-conditioning equipment (or other motor-operated equipment) should

not be placed on the same ac line that powers the system.

— The table below lists the maximum VA ratings and BTU/hour ratings for all

instruments in the system. This table can be used to determine both the

electrical requirements and the air conditioning requirements of the system

Summary of Contents for N5290A

































































































Search results

Summary of Contents for N5290A

Reviews:

Related manuals for N5290A

Brands by name

Popular brands

Keysight Technologies N5290A, Installation Manual

Search results

Summary of Contents for N5290A

Reviews:

Related manuals for N5290A

Brands by name

Popular brands