Keysight Technologies N5290A Installation Manual Download Page 58

Page: 58 / 96

3- 10 Keysight N5290/1A Installation Guide

System Installation
PNA, Controller, and Test Head Module Interconnections

Secure the analyzer’s lower locking feet (N5240-20092 and N5240-20095)

to the test set’s upper locking feet (N5292-20012 and N5292-20013)

using the spring–loaded screws on the locking feet. Refer to

Figure 3-5

. If

the locking feet are not aligned with the screw holes in the test set's upper

locking feet, loosen the screws securing the feet to the instrument slightly

to align and tighten.

Figure 3-5

Install N5292A test set controller to the bottom of the PNA using vertical links

and upper foot locks (N5292-20012 and N5292-20013). Long foot lock

screws shown, but short lock screws are similar.

Summary of Contents for N5290A

































































































Search results

Summary of Contents for N5290A

Reviews:

Related manuals for N5290A

Brands by name

Popular brands

Keysight Technologies N5290A, Installation Manual

Search results

Summary of Contents for N5290A

Reviews:

Related manuals for N5290A

Brands by name

Popular brands