Keysight Technologies N5290A Installation Manual Download Page 64

Page: 64 / 96

3- 16 Keysight N5290/1A Installation Guide

System Installation
PNA, Controller, and Test Head Module Interconnections

N5290/1A Option 403—(Interconnect Kit N5292-60017)

Figure 3-11 on page 16

is used for the N5292-60017 interconnect kit.

Figure 3-11

N5290/1A-403: Install semirigid cables (N5292-20014, N5292-20015, and

N5292-20016) to the front panel of the PNA and N5292A

IMPORTANT!

The N5227B and N5247B interconnect kits contain 2.4 mm to 3.5 mm

cables. It is important to connect the 2.4 mm end to the PNA and to

connect the 3.5 mm end to the N5292A test set controller. Improper

connections will result in damage to your instruments.
It is important to use two wrenches when connecting the semirigid cables

to the 1/2/3/4 port 1.85 mm outputs front ports of the PNA to avoid

stressing the connectors and causing damage to your PNA (i.e., the

2.4 mm cable end is compatible with the 1.85 mm connector of the PNA).

Summary of Contents for N5290A

































































































Search results

Summary of Contents for N5290A

Reviews:

Related manuals for N5290A

Brands by name

Popular brands

Keysight Technologies N5290A, Installation Manual

Search results

Summary of Contents for N5290A

Reviews:

Related manuals for N5290A

Brands by name

Popular brands