Keysight Technologies N5290A Installation Manual Download Page 21

Page: 21 / 96

Keysight N5290/1A Service Guide 1-15

Safety and Regulatory Information
Space Requirements

Space Requirements

Standard installation of the N5290/1A system includes configuration and

installation of the system on a customer provided lab bench or table top of

adequate size and strength.

N5290/1A System Weight and Dimensions

Component Weight and Dimensions

Table 1-4

shows the maximum weight and dimensions of the N5290/1A

system components. Refer also to

Table 1-5 on page 16

for test head module

dimensions.

Table 1-4

N5290/1A System Weight and Dimensions

Model

Weight

Required Benchtop Dimensions for the System

Clearance

Width

Depth

2-Port

60.1 kg (132 lb)

48 cm (19 in)

178 cm (70 in)

114 cm (45 in)

4-Port

83.5 kg (183.2 lb)

48 cm (19 in)

178 cm (70 in)

140 cm (55 in)

Summary of Contents for N5290A

































































































Search results

Summary of Contents for N5290A

Reviews:

Related manuals for N5290A

Brands by name

Popular brands

Keysight Technologies N5290A, Installation Manual

Search results

Summary of Contents for N5290A

Reviews:

Related manuals for N5290A

Brands by name

Popular brands