Keysight Technologies N5290A Installation Manual Download Page 50

Page: 50 / 96

3- 2 Keysight N5290/1A Installation Guide

System Installation
Getting Prepared

Getting Prepared

To successfully install this N5290/1A system, you will need the following:

— An ESD-safe work area - refer to

“Electrostatic Discharge Protection” on

page 1-7

— Sufficient AC power – refer to

“Site Preparation” on page 1-17

— Correct tools for system validation - refer to

“Tools Required for the

Installation” on page 3-2

— Enough time - refer to

“About Installing the System” on page 3-2

Tools Required for the Installation

About Installing the System

The N5290/1A contains extremely sensitive components that can be

ruined if mishandled. Follow instructions carefully when making cable

connections, especially wire harness connections.
The person performing the work accepts responsibility for the full cost of

the repair or replacement of damaged components.

Description

Qty

Part Number

T-10 TORX driver (set to 9 in-lbs)

N/A

T-20 TORX driver (set to 21 in-lbs)

N/A

5/16-in torque wrench (set to 8 in-lbs)

N/A

5/16-in torque wrench (set to 10 in-lbs)

N/A

5/16-in torque wrench (set to 21 in-lbs)

N/A

14 mm open-end wrench (set to 4 in-lbs)

N/A

20 mm open-end wrench (set to 8 in-lbs)

N/A

Use a 5/16-in torque wrench set to 8 in-lbs on all semirigid front and rear

panel cable connections.

Products affected

N5290A, N5291A, N5292A, N5293A, and N5295A.

Installation to be performed by

Keysight customer engineer or personnel qualified by Keysight

Estimated installation time

4 hours

Estimated full instrument verification time 4.0 hours

Summary of Contents for N5290A

































































































Search results

Summary of Contents for N5290A

Reviews:

Related manuals for N5290A

Brands by name

Popular brands

Keysight Technologies N5290A, Installation Manual

Search results

Summary of Contents for N5290A

Reviews:

Related manuals for N5290A

Brands by name

Popular brands