Keysight Technologies N5290A Installation Manual Download Page 67

Page: 67 / 96

Keysight N5290/1A Installation Guide 3-19

System Installation
PNA, Controller, and Test Head Module Interconnections

N5293/5A Modules Front Panel Cabling

The front-panel connections between the millimeter head controller and a test

head module are shown in

Figure 3-15 on page 20

through

Figure 3-18 on

page 21

. This cabling is duplicated for each test head module in the system.

—

“N5292A Option 200 2–Port Cable Connections” on page 3-20

—

“N5292A Option 400 4–Port Cable Connections” on page 3-21

Connections for Each Head

Connect a set of x4 feet to the bottom of each millimeter module.
Choose either:

—

N5293-40003 feet, bottom, grip or

—

N5293-40004 feet, bottom, slip

2. PNA/PNA-X

: Verify you have connected all of the semirigid cables and

torque to 8 in-lbs. Refer to

Figure 3-8 on page 13

3. N5292A

: Connect the integrated cables from the N9293A or N5295A

millimeter heads.

IMPORTANT!

In order to maintain compliance to the certificate of calibration it is

recommended that the frequency extenders be connected to the

corresponding test set ports per the Certificate of Calibration provided.

IMPORTANT!

Before connecting the millimeter-wave modules, verify that the test set

and the power supplies (if used) are powered down.
The N5292A test set controller’s integrated front panel connectors contain

optical sensors to ramp power up or down gradually when the N5293/5A

millimeter modules are connected to prevent damage. Refer to

“Troubleshooting the N5293/5A Millimeter Modules” on page 3-26

IMPORTANT!

When connecting the N5293/5A modules, it is very

important to verify that the module connectors are seated flush and that

the screws are screwed all the way into the N5292A front test ports. But,

be careful to

not

overtighten.

IMPORTANT!

In order to maintain compliance to the certificate of calibration it is

recommended that the frequency extenders be connected to the

corresponding test set ports per the Certificate of Calibration provided.

Summary of Contents for N5290A

































































































Search results

Summary of Contents for N5290A

Reviews:

Related manuals for N5290A

Brands by name

Popular brands

Keysight Technologies N5290A, Installation Manual

Search results

Summary of Contents for N5290A

Reviews:

Related manuals for N5290A

Brands by name

Popular brands