Keysight Technologies N5290A Installation Manual Download Page 54

Page: 54 / 96

3- 6 Keysight N5290/1A Installation Guide

System Installation
PNA, Controller, and Test Head Module Interconnections

PNA, Controller, and Test Head Module Interconnections

System Setup

Mount the analyzer on top of the test set before connecting any cables to the

PNA or to the test set. The cables can then be connected after the analyzer
and test set are securely attached.

If not already done, open the interconnect kit and validate its contents against

Table 2-6 on page 2-11

Mounting a Network Analyzer on the Test Set

Refer to the following kits for your specific analyzer. In this procedure a various

PNAs are used with a N5292A Test Set Controller. But, other PNAs are similar.

— Interconnect kits includes the SMA 50 ohm loads, cables, upper and lower

locking feet, and screws. Refer to

Table 2-6 on page 2-11

IMPORTANT!

The N5227B and N5247B interconnect kits contain 2.4 mm to 3.5 mm

cables. It is important to connect the 2.4 mm end to the PNA and to

connect the 3.5 mm end to the N5292A test set controller. Improper

connections will result in damage to your instruments.
It is important to use two wrenches when connecting the semirigid cables

to the 1/2/3/4 port 1.85 mm outputs front ports of the PNA to avoid

stressing the connectors and causing damage to your PNA (i.e., the

2.4 mm cable end is compatible with the 1.85 mm connector of the PNA).

The network analyzer is heavy. It is recommended that two

individuals, or a mechanical lift be used to lift or transport the

instrument.

Summary of Contents for N5290A

































































































Search results

Summary of Contents for N5290A

Reviews:

Related manuals for N5290A

Brands by name

Popular brands

Keysight Technologies N5290A, Installation Manual

Search results

Summary of Contents for N5290A

Reviews:

Related manuals for N5290A

Brands by name

Popular brands