Keysight Technologies N5290A Installation Manual Download Page 17

Page: 17 / 96

Keysight N5290/1A Service Guide 1-11

Safety and Regulatory Information
Regulatory Information

South Korean Class A EMC declaration:

This equipment has been conformity assessed for use in business
environments. In a residential environment this equipment may cause
radio interference.

—

This EMC statement applies to the equipment only for use in
business environment.

Safety

Complies with the essential requirements of the European Low Voltage

Directive as well as current editions of the following standards (dates and

editions are cited in the Declaration of Conformity:

— IEC/EN 61010-1
— Canada: CSA C22.2 No. 61010-1
— USA: UL std no. 61010-1

Acoustic Statement: (European Machinery Directive)

To find a current Declaration of Conformity for a specific Keysight product, go

to:

http://www.keysight.com/go/conformity

Acoustic noise emission

LpA <70 dB

Operator position

Normal operation mode per ISO 7779

Summary of Contents for N5290A

































































































Search results

Summary of Contents for N5290A

Reviews:

Related manuals for N5290A

Brands by name

Popular brands

Keysight Technologies N5290A, Installation Manual

Search results

Summary of Contents for N5290A

Reviews:

Related manuals for N5290A

Brands by name

Popular brands