background image

1. Press «UP» repeatedly until 

Local mode is displayed as the active line.

2. Press «Enter» to switch into setting mode.

Operating mode flashes.

  8 9   p s i           0 8 : 1 5             1 7 6   ° F

5.2.3 Load control

Menu

Local mode pA/pB Cycle

Active line

·········
Remote mode :      pA
Key remote :      ☐
·········
current pA/pB Cycle

Display of the current operating mode

3. Press the «UP» or «DOWN» key to select the required operating mode (pA, pB, pA/pB Clock

or pA/pB Cycle).

4. Press «Enter» to accept the setting.

The actual operating mode is displayed.

5. Press «Esc» repeatedly to return to the Main Menu.

Result The clock is fully configured.

7.9  Configuring the machine for master control

7.9.1  List of the various master controllers

The machine controller is provided with several methods of working under other controllers.

Method

Description

Section

Master control with Profibus

(requires an additional module)

The controller (and therefore the compressor)

receives the instruction LOAD, IDLE or local

operation via the Profibus master (e.g.

SIGMA AIR MANAGER or VESIS). The system

setpoint pressures pA and pB are irrelevant for

the LOAD/IDLE signals.

7.9.2

Master control of two compressors with

SIGMA CONTROL 2  via Ethernet inter‐

face

2 The SIGMA CONTROL 2 controllers operate

as master and slave. The slave receive the

command to switch between the two system

setpoint pressures pA and pB from the master.

7.9.4

Master control via LOAD remote contact.
Master control via a LOAD remote con‐

tact is another method of controlling the

machine externally. There are 2 possibil‐

ities:

LOAD remote contact

An input signal from a superordinate controller

switches the machine to LOAD or IDLE. The

setpoint pressure settings pA and pB have no

relevance.

7.9.5

Local/LOAD remote contact:

Using two inputs, a master controller (e.g.

MVS 8000) switches the machine between

LOAD/IDLE and local operation.

7.9.6

7

Initial Start-up

7.9

Configuring the machine for master control

9_9450 03USE

Service manual    Controller  
SIGMA CONTROL 2  SCREW FLUID 1.1.3

87

Summary of Contents for ESD 352 SFC






























































































































































































































































































































































































































Reviews: