manualshive.com logo in svg

JVC GV-LS2, User Manual, Page: 96 / 172

Share
Download
JVC GV-LS2 User Manual Download Page 96

20

       

 

Setting Up You Camera's DDNS Account

    

 

(1) Using Internet Explorer, go into your camera’s Settings.

    

 

    

 

URL to access Settings: http://(camera’s IP address):8000

    

 

    

 

Ex. Enter http://192.168.1.100:8000 into the address bar.

    

 

The camera’s IP address varies depending on your network environment.

    

 

Use the following method if you do not know your camera’s IP address:

    

 

    

 

(i) Open JVC CAM Control on your computer.

    

 

    

 

(ii) Check the camera’s IP address displayed on the right.

    

 

• JVC CAM Control must be installed on your computer in advance.

    

 

  

The computer and camera should be connected to the same Wi-Fi router.

    

 

• If you cannot find your camera’s IP address (if it is not displayed) even 

    

   

when using JVC CAM Control, refer to the Settings screen on your router.

Note

2

Summary of Contents for GV-LS2













































































































































































Reviews:

No comments