manualshive.com logo in svg

JVC GV-LS2, User Manual, Page: 30 / 172

Share
Download
JVC GV-LS2 User Manual Download Page 30

30

Preparation

Connecting to the camera

DIRECT WLAN

RESET

LAN(OFF)

ETHERNET

DC

AV

MIC

PLUG IN POWE

R

Attaching to the hot shoe

1 

Remove the hot shoe cover.

2 

Attach the mic.

Connecting to the pantilter

MIC

POWER

PLUG IN

AV

DC

EXTEND

Connecting an External Mic

Connect an external mic to record external sounds.
Connect a commercially available mic to the MIC terminal of the pantilter when it is attached, or of the camera when 
not attached.

•  Use the plug-in power type.
•  Do not use microphone with L-shaped connectors.
•  Turn off the power before connecting/disconnecting the mic.
•  Without an external mic, the internal mic can record ambient sounds.
•  When the sounds are too loud or too low, change the "MIC LEVEL SETTING". ( 

➭

 page 45)

Mic (commercially available)

f

3.5 mm stereo mic jack

Mic (commercially available)

f

3.5 mm stereo mic jack

Summary of Contents for GV-LS2













































































































































































Reviews:

No comments