manualshive.com logo in svg

JVC GV-LS2, User Manual, Page: 32 / 172

Share
Download
JVC GV-LS2 User Manual Download Page 32

32

Use

Using the Unit Alone

Insert an SD card and attach the battery, so you can carry and use the unit as a normal video camera. Set whether 
to save recorded videos to the SD card or stream them wirelessly. ( 

➭

 page 41)

Turning on/off the power

Turning on the power
Press and hold the power button.
The record button starts blinking. Wait until it stops 
blinking and off.

Turning off the power
Press and hold the power button again.
The power button turns off.

Starting/Stopping recording

Starting recording
Press the record button.
The record button blinks.
The button blinks quickly for 2 seconds if recording 
cannot start. Check the SD card or unit settings.

Stopping recording
Press the record button again.
The record button turns off.

CAUTION

•  The power is automatically turned off if "AUTO 

POWER OFF" is set to "ON", the unit runs with the 
battery, and no operation is performed for 5 minutes. 
( 

➭

 page 46)

•  Recording stops automatically as it cannot be 

performed for 12 or more consecutive hours.

Summary of Contents for GV-LS2













































































































































































Reviews:

No comments