JVC GV-LS2 User Manual Download Page 28

Page: 28 / 172

Preparation

Inserting

Insert the card straight with the terminal side facing
right.

• Make sure that the write protect switch of the SD

card is not set to LOCK (writing protected).

Removing

Push the card in once, and pull it out straight.

Inserting/Removing an SD Card

Insert a separately purchased SD card to save recorded data to the card. The saved data can be deleted/
downloaded from a browser.

• Turn off the power before inserting/removing the SD card.
• The saved data can be played back by Windows Media Player 12 (

➭

page 37).

Compatible SD cards

Operation confirmed with the following SD cards.

Manufacturer

Panasonic
TOSHIBA
SanDisk

Video

Class 4 or higher compatible SD
card (2 GB)
Class 4 or higher compatible SDHC
card (4 GB to 32 GB)
Class 4 or higher compatible SDXC
card (48 GB to 64 GB)
(When recording with video
quality "UXP", Class 6 or higher is
recommended.)

• Using SD cards (including SDHC/SDXC cards) other

than those specified above may result in recording
failure or data loss.

• Not all SD card operations are guaranteed.

Some operations may not be performed due to
specification changes, etc.

• Do not touch the terminals of the SD card. Doing so

may cause data loss.

Approximate recording times

Mode

Capacity

4 GB

8 GB

16 GB

32 GB

48 GB

64 GB

UXP

20 min.

40 min.

1 hr. 20 min.

2 hr. 50 min.

4 hr. 10 min.

5 hr. 40 min.

30 min.

1 hr.

2 hr.

4 hr.

6 hr.

8 hr. 10 min.

40 min.

1 hr. 20 min.

2 hr. 50 min.

5 hr. 50 min.

8 hr. 30 min.

11 hr. 30 min.

1 hr. 40 min.

3 hr. 30 min.

7 hr. 10 min.

14 hr. 40 min.

21 hr. 30 min.

28 hr. 50 min.

The above times are only intended as an approximate guide. They may be shorter depending on the recording
situation.

Summary of Contents for GV-LS2













































































































































































Search results

Summary of Contents for GV-LS2

Reviews:

JVC GV-LS2, User Manual, Page: 28 / 172

Search results

Summary of Contents for GV-LS2

Reviews: