manualshive.com logo in svg

JVC GV-LS2, User Manual, Page: 29 / 172

Share
Download
JVC GV-LS2 User Manual Download Page 29

29

Preparation

Attaching/Removing the Battery

The camera can run with the battery power only. When the battery (BN-VG139U) (sold separately) is attached, 
videos can be transmitted/recorded even in places where the AC adapter cannot be used.

•  The battery cannot be used when the pantilter is attached.
•  Turn off the power before attaching/removing the battery.
•  The following cannot be used while the battery is attached:

– LAN terminal, network mode switch, reset button

CAUTION

•  Be sure to use a battery of our manufacture. If a battery not of our manufacture is used, the safety and 

performance are not guaranteed.

•  Charging may take time or may not be possible in places outside the operating temperature range. 

Attaching

Insert the battery deeply, and then slide it to the right 
until it clicks.

Removing

Slide the battery to the left, and pull it out toward you 
while pushing in the lever below the battery.

Charging

Connect the adapter to the DC connector of the 
camera, and turn off the power. Charging starts. 
The power button of the camera blinks during charging. 
The power button turns off when charging is complete.

Approximate charging times

Charging time

BN-VG139U (sold 
separately)

6 hr. 10 min.

Approximate recording times

Actual 

shooting time

Continuous 

shooting time

BN-VG139U (sold 
separately)

1 hr. 55 min.

2 hr. 55 min.

Summary of Contents for GV-LS2













































































































































































Reviews:

No comments