Juniper JUNOSE 11.2.X IP SERVICES Configuration Manual Download Page 269 | Manualshive

Page: 269 / 356

background image

5.

Configure a physical or loopback interface for the end of the tunnel on virtual router
chicago.

host1:chicago(config)#

interface atm 12/1.5

host1:chicago(config-if)#

ip address 10.6.6.6 255.255.255.0

6.

Configure the tunnel interface on virtual router chicago.

a.

Create the tunnel interface.

The name of the tunnel interface can differ from the tunnel interface configured
in Step 3.

host1:chicago(config-if)#

interface tunnel gre:BostonTunnel

b.

Configure the source and destination points of the tunnel interface.

The destination of this tunnel interface matches the source of the tunnel interface
configured in Step 3 and vice versa.

host1:chicago(config-if)#

tunnel source 10.6.6.6

host1:chicago(config-if)#

tunnel destination 10.5.5.5

c.

Set the MTU for the tunnel.

The MTU must match the MTU configured in Step 3.

host1:chicago(config-if)#

tunnel mtu 8000

d.

Configure the IP address of the tunnel interface.

host1:chicago(config-if)#

ip address 10.9.9.9 255.255.255.0

Configuring IP Tunnels to Forward IP Frames

When a line module receives IP frames destined for a tunnel, the module forwards the
frames to a tunnel-service module. Tunnel-service modules include SMs and modules
that support the use of shared tunnel-server ports.

The tunnel-service module encapsulates the frames and forwards them to the tunnel
through an interface determined by a route lookup of an IP frame. The source and
destination addresses in the IP frame are the source and destination addresses of the
tunnel.

Similarly, when a line module receives traffic from a tunnel, the module forwards the
traffic to the tunnel-service module for deencapsulation. After deencapsulation, the
tunnel-service module forwards the resulting IP frames to an interface determined by a
route lookup.

When you have configured a tunnel interface, treat it in the same way as any IP interface
on the router. For example, you can configure static IP routes or enable routing protocols
on the tunnel interface. The IP configurations you apply to the tunnels control how traffic
travels through the network.

Preventing Recursive Tunnels

If routing information about the tunnel network combines with routing information about
the transport networks (the networks that the tunnel services), a

recursive

tunnel can

243

Copyright © 2010, Juniper Networks, Inc.

Chapter 9: Configuring IP Tunnels

«
...
267
268
269
270
271
...
»

Summary of Contents for JUNOSE 11.2.X IP SERVICES





































































































































































































































































































































































Reviews:

No comments

Related manuals for JUNOSE 11.2.X IP SERVICES

Brand: Samsung Pages: 16

SCX 4826FN - Laser Multi-Function Printer

Brand: Samsung Pages: 16

TEMS VISUALIZATION 7.2 ENTERPRISE

Brand: ASCOM Pages: 8

Configuring snom phones for Mass Deployment

Brand: Snom Pages: 22

ADS INSTANT MUSIC

Brand: ADS Technologies Pages: 5

MOBILE SECURITY 80 Series

Brand: F-SECURE Pages: 39

Brand: TC Electronic Pages: 22

Brand: British Telecom Pages: 4

Brand: Ulead Pages: 58

Brand: Avaya Pages: 48

Brand: M-Audio Pages: 99

CODESOFT Sentinel Print Pack

Brand: Techniques Avancees Pages: 50

1210SA - Serial ATA RAID Controller

Brand: Adaptec Pages: 88

Brand: Texas Instruments Pages: 52

Brand: Texas Instruments Pages: 37

ITANIUM ARCHITECTURE - SOFTWARE DEVELOPERS VOLUME 3 REV 2.3

Brand: Intel Pages: 1898

Brand: Xerox Pages: 60

Brand: LXE Pages: 260

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands