E 29
0306
.GB
5.4
Slack chain safety device override
If the slack chain safety device has applied, e. g. when positioning
the load handler, loosening or braking the lift chain, the “slack
chain safety device” symbol (63) illuminates in the display unit. It
is possible to raise the Main Lift if the slack chain safety device
override switch (39) is depressed and held down while pressing
the hydraulic control knob. Travelling and lowering are now
inhibited.
Before starting again, rectify the damage.
M
The truck may only be started again once the damage has been removed.
5.5
Travel cutout override (
o
)
KIf travel is inhibited from a certain lift height (the “Travel cutout
override” symbol (65) appears in the display), but the position of
the truck relative to the rack must be adjusted to load or unload
goods, press the “unlock travel” switch (39) and apply the travel
control knob as described in “Travelling”. This allows you to travel
at crawl speed.
5.6
Lift limit override (
o
)
If local conditions require, an automatic lift cutout to apply from a
given lift height can be fitted for safety reasons. The display unit
shows the "Lift Cutout Override" symbol (67).
M
Lift cutout only becomes effective after a test run has been carried
out. You can tell when this is the case because the actual height
is shown in the display unit.
Pressing the “lift cutout override” switch (39) disables the lift
cutout.
F
When disabling the lift cutout the driver must look out for
obstacles when the mast is extended.
Z
Lift cutout is re-activated each time the mast falls below the lift limit height.
The respective travel and lift limit switches are located in the control panel.
63
39
65
39
67
39
E 29
0306
.GB
5.4
Slack chain safety device override
If the slack chain safety device has applied, e. g. when positioning
the load handler, loosening or braking the lift chain, the “slack
chain safety device” symbol (63) illuminates in the display unit. It
is possible to raise the Main Lift if the slack chain safety device
override switch (39) is depressed and held down while pressing
the hydraulic control knob. Travelling and lowering are now
inhibited.
Before starting again, rectify the damage.
M
The truck may only be started again once the damage has been removed.
5.5
Travel cutout override (
o
)
KIf travel is inhibited from a certain lift height (the “Travel cutout
override” symbol (65) appears in the display), but the position of
the truck relative to the rack must be adjusted to load or unload
goods, press the “unlock travel” switch (39) and apply the travel
control knob as described in “Travelling”. This allows you to travel
at crawl speed.
5.6
Lift limit override (
o
)
If local conditions require, an automatic lift cutout to apply from a
given lift height can be fitted for safety reasons. The display unit
shows the "Lift Cutout Override" symbol (67).
M
Lift cutout only becomes effective after a test run has been carried
out. You can tell when this is the case because the actual height
is shown in the display unit.
Pressing the “lift cutout override” switch (39) disables the lift
cutout.
F
When disabling the lift cutout the driver must look out for
obstacles when the mast is extended.
Z
Lift cutout is re-activated each time the mast falls below the lift limit height.
The respective travel and lift limit switches are located in the control panel.
63
39
65
39
67
39
Summary of Contents for EKS 308
