JR ProPo Ergo Z230 Assembly Instructions Manual Download Page 26

Page: 26 / 72

4-9

FLYBAR INSTALLATION

Thread each flybar paddle onto the Flybar until the
threaded tip of the Flybar protrudes approximately 6mm.

Adjust each Flybar Paddle so they are parallel to the Flybar
Control Arms and to each other. Secure the Flybar Paddles
using two 4mm Lock Nuts.

*Note: Slide the Flybar Weights onto the Flybar before

installation of the Flybar Paddles. For increased
cyclic response (3D Flight), Flybar Weights
should be omited.

Note proper direction of each Flybar Paddle
(short portion forward, clockwise rotation)

* Flybar Weight (2 pc)

4x4mm Set Screw

(2 pc)

6mm

Flybar Paddles

4mm Lock Nut

(2 pc)

4x4mm Set Screw (2 pc)

4mm Washer (2pc)

Flybar Control Arm (2 pc)

Flybar

Note:

Center the Flybar in the Seesaw Shaft before
securing the two Flybar Control Arms

Check to insure that the two Flybar Control Arms

are parallel to the center line of the Flybar

....2 pc

4x4mm Set Screw

....2 pc

4mm Nut

....2 pc

Steel Joint Ball

....2 pc

2x8mm Flat Head Screw

....2 pc

4mm Washer

Use Threadlock

Attach the Steel Control Ball to the
Flybar Control Arm (2) as shown.

Flybar Control Arm (2 pc)

2x8mm Flat Head

Screw (2 pc)

4-10

FLYBAR PADDLE ATTACHMENT

Steel Control Ball

(2 pc)

4x4mm Set Screw

Z,Q

Summary of Contents for Ergo Z230









































































Search results

Summary of Contents for Ergo Z230

Reviews:

Related manuals for Ergo Z230

Brands by name

Popular brands

JR ProPo Ergo Z230, Assembly Instructions Manual

Search results

Summary of Contents for Ergo Z230

Reviews:

Related manuals for Ergo Z230

Brands by name

Popular brands