JR ProPo Ergo Z230 Assembly Instructions Manual Download Page 11

Page: 11 / 72

1-6

FUEL TANK ASSEMBLY

1. Cut the small Gasoline Tubing

(included) to a length of 77mm. Next,
connect the Fuel Tank Clunk, Nipple, and
medium Gasoline Fuel Tubing (not
included) as shown below.

2. Insert the assembly above (Fuel Tank

Clunk first) into the Fuel Tank opening so
that the Nipple is inside the tank. Next,
slide the Fuel tank Grommet over the
medium Fuel Tubing.

3. Insert the Fuel Tank Grommet into the

Fuel Tank opening, making sure that it is

fully seated.

Make sure Grommet is

fully seated.

6. Completed Assembly

4. Pull the medium Gasoline Fuel Tubing

out of the Fuel Tank until the threads of
the Fuel Tank Nipple are exposed.

5. Remove the medium Gasoline Fuel Tubing

from the Nipple and secure the Nipple to
the Fuel Tank using the 7x12x1mm Washer
and 7mm Nut supplied. Be sure to
secure this assembly firmly to avoid leakage.

Gasoline Fuel Tubing (not included)

Connects to Muffler Pressure Tap

Medium Gasoline Fuel Tubing (not included)

Connects to Engine Carburetor

Nipple

Fuel Tank Grommet

Pull out until

Nipple threads

are exposed

7x12x1 Washer

7mm Nut

Use two Wrenches

if necessary to

secure Tank Nipple.

Gasoline Fuel

Tubing (Small)

Fuel Tank

Clunk

77mm

Z,Q

Note: The Fuel Tank Fittings included in the Z230

kit are made specifically for gasoline use.

Summary of Contents for Ergo Z230









































































Search results

Summary of Contents for Ergo Z230

Reviews:

Related manuals for Ergo Z230

Brands by name

Popular brands

JR ProPo Ergo Z230, Assembly Instructions Manual

Search results

Summary of Contents for Ergo Z230

Reviews:

Related manuals for Ergo Z230

Brands by name

Popular brands