manualshive.com logo in svg

JR ProPo Ergo Z230, Assembly Instructions Manual

Share
Download
JR ProPo Ergo Z230 Assembly Instructions Manual Download Page 8

8

1-1

4x4mm Set Screw

Use Threadlock

..........1 pc

3x6mm Socket Head Bolt

...1 pc

3mm Flat Washer

.........1 pc

CLUTCH BELL/START SHAFT ASSEMBLY

1-2

TAIL DRIVE PINION/BEARING BLOCK ASSEMBLY

Install the Lower Bearing Block so the
bearing face is toward the top

Install the Upper Bearing Block so the
bearing is toward the bottom

Tail Drive Pinion

Bearing Blocks

Tail Drive Pinion

with Shaft

Front Tail Belt Pulley
(Install Flat Side Up)

3mm Flat Washer

3x6mm Socket Head Bolt (Use  Red Threadlock)

Complete Assembly

4x4mm Set Screw (Use Threadlock)

Starter Hex Adaptor

Start Shaft Bearing Block

Note: These items are

pre-assembled

Start Shaft

Clutch Bell Assembly

Be sure that the Bearing with

the 5mm ID faces upward

Pinion Gear  (13T)

(Use Threadlock when

assembling)

Complete Assembly

Note: It will be necessary to 

press the two Bearings 
into the Bearing Blocks. 
Press the Bearings in 
evenly by hand. Do not 
use a vise or pliers for 
this procedure as 
damage could result.

Use Red Threadlock

RED

RED

UP

UP

Bearing

Bearing

Z,Q

Z,Q

*

*

Summary of Contents for Ergo Z230









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands