JR ProPo Ergo Z230 Assembly Instructions Manual Download Page 28

Page: 28 / 72

5-1

TAIL OUTPUT SHAFT/PULLEY ASSEMBLY

5-2

TAIL GEAR CASE ASSEMBLY

Tail Output Shaft

Longer

Distance

Tail Case Pulley

Spring Pin

Adjustable Pliers

Press pin into this hole

Note correct direction of Tail
Output Shaft during assembly

Press in Spring Pin gently using
adjustable pliers. Be sure to center
pin through the Tail Case Pulley
when completed.

3x10mm Socket Head Bolt

Tail Gear Case (L/R)

Tail Output
Shaft Bearing

Tail Output Shaft
Bearing

Tail Drive Belt

80mm

Longer (Helicopter)

Shorter (Tail Gear Case)

2.6mm Hex Nut (6 pc)

Tail Boom

2.6mmx10mm

Socket Head

Bolt (6 pc)

3x10mm

Socket Head Bolt

Wrap tape around the end of the
Tail Drive Belt temporarily to ease
insertion through the Tail Boom .
Be careful not to “kink” the Tail
Drive Belt.

Note: Be sure to position the

Tail Gear Case onto the
shorter slotted side of
the Tail Boom.

....1 pc

Spring Pin

Use Threadlock

....3 pc

....6 pc

2.6x10mm Socket Head Bolt

....6 pc

2.6mm Hex Nut

....2 pc

Tail Output Shaft Bearing

3x10mm Socket Head Bolt

Z,Q

Summary of Contents for Ergo Z230









































































Search results

Summary of Contents for Ergo Z230

Reviews:

Related manuals for Ergo Z230

Brands by name

Popular brands

JR ProPo Ergo Z230, Assembly Instructions Manual

Search results

Summary of Contents for Ergo Z230

Reviews:

Related manuals for Ergo Z230

Brands by name

Popular brands