JR ProPo Ergo Z230 Assembly Instructions Manual Download Page 27

Page: 27 / 72

4-11

ROTOR HEAD/SWASHPLATE CONTROL ROD INSTALLATION

Thread the Universal Links onto the threaded Control Rods to the lengths shown below. Please note that all
links should be adjusted so that when attached to the Control Ball, the words “JR Propo” are to the outside.

CONTROL ROD ASSEMBLY

SEESAW ARM TO MAIN BLADE HOLDER

(2.3x15mm Threaded Rod)

WASHOUT ARM TO FLYBAR CONTROL ARM

SWASHPLATE TO ROLL BELLCRANK

(2.3x30mm Threaded Rod)

8mm

19mm

SWASHPLATE TO SEESAW ARM

(2.3x40mm Threaded Rod)

Universal Link

Universal Link (Short)

Double Link (Long)

(1 pc)

Adjust so Links are

90° to each other.

Universal Link

x 2

0° main blade pitch at
center stick (3D Setup)

1mm

3mm

5° main blade pitch at center stick

(normal/beginner)

x 1

x 2

Z,Q

Summary of Contents for Ergo Z230









































































Search results

Summary of Contents for Ergo Z230

Reviews:

Related manuals for Ergo Z230

Brands by name

Popular brands

JR ProPo Ergo Z230, Assembly Instructions Manual

Search results

Summary of Contents for Ergo Z230

Reviews:

Related manuals for Ergo Z230

Brands by name

Popular brands