manualshive.com logo in svg

JR ProPo Ergo Z230, Assembly Instructions Manual

Share
Download
JR ProPo Ergo Z230 Assembly Instructions Manual Download Page 17

3-1

MAIN DRIVE GEAR/AUTOROTATION ASSEMBLY

3-2

MAIN DRIVE GEAR/AUTOROTATION ASSEMBLY INSTALLATION

17

3x6mm Socket Head Bolt (4 pc)
Tighten equally to prevent
warping of Main Drive Gear

Main Drive Gear

Autorotation Assembly

4x4mm Set Screw (4 pc)

Main Shaft Collar

Main Rotor Shaft

14mm

3mm

4x4mm Set Screws (4pc)

1.  Secure the Autorotation Hub to the Main Rotor Shaft 

using four 4x4mm Set Screws. Next, slide the 
Main Shaft Collar onto the Main Rotor Shaft. While 
pulling upward on the Main Rotor Shaft, secure the 
Main Shaft Collar to the Main Rotor Shaft using the 
remaining four 4x4mm Set Screws.

2.

Once the Main Shaft Assembly is in place, adjust the gear mesh of the Clutch Bell 
and Tail Belt Pinion Gears, and secure the bolts left loose from Step 2-1.

3x6mm Socket Head Bolt

.......4 pc

4x4 Set Screw

.......8 pc

Use Threadlock

Use Threadlock on all

screws in this assembly

Z,Q

Z,Q

When assembling, be sure that two of
the four 4mm Set Screws engage into
the through hole in the bottom of the
Main Rotor Shaft.

Summary of Contents for Ergo Z230









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands