JR ProPo Ergo Z230 Assembly Instructions Manual Download Page 14

Page: 14 / 72

2-4

FUEL TANK INSTALLATION

Assembled

Fuel Tank

3x8mm Socket Head Bolt (2pc)

Tank Mounting Rubber

Attach a small piece of
double sided 1/8" servo tape
(not included) to the inside of
the two tank holders prior to
installation.

Note: Select the correct Tank
Mounting Rubber as follows:
Ergo Z230: Grey (Soft)
Ergo Quattro: Black (Hard)

Note: Install the Fuel Tank and Tank Mounting
Rubber into the lower frame halves before
attaching the Main Frame Standoffs.

When securing Standoffs to Frame, position
the bottom of the frame on a level surface to
prevent twisting during tightening.

Also be sure to use the correct length bolt in
the correct location when assembling.

Main Frame Standoff (2pc)

3x10mm Socket Head Bolt (4pc)

Fuel Tank Holder

(2pc)

3mm Lock

Nut (2pc)

......2 pc

3x8mm Socket Head Bolt

......2 pc

3mm Lock Nut

Main Frame Standoff, 80mm

2-3

LOWER MAIN FRAME ASSEMBLY

3x10mm Socket Head Bolt

Use Threadlock

Use Threadlock on all

screws in this assembly.

......4 pc

...3 pc

3x8mm Sockethead Bolt (4pc)

ERGO Z230 ONLY

Lower Frame Angle (2pc)

* Note: Make sure that the frames are positioned

so that the counter sunk screw holes face

towards the inside of the Main Frame

Assembly as shown.

4x12mm

Socket Head Bolt

4mm Nut

*Counter Sunk Holes 3x8mm Socket Head Bolt

(Use Threadlock)

3mm Lock Nut (8pc)

3x10mm (4pc)
Flat Head Screw

Lower Main
Frame Halves

......8 pc

2.6x8mm Self Tapping Screw

......4 pc

3x10mm Flat Head Screw

......4 pc

....10 pc

3x8mm Socket Head Bolt

3mm Lock Nut

......1 pc

....1 pc

4x12mm Socket Head Bolt

4mm Lock Nut

Servo Installation Plate

2.6x8mm

Self Tapping Screw

ERGO Z230 ONLY

Z,Q

Summary of Contents for Ergo Z230









































































Search results

Summary of Contents for Ergo Z230

Reviews:

Related manuals for Ergo Z230

Brands by name

Popular brands

JR ProPo Ergo Z230, Assembly Instructions Manual

Search results

Summary of Contents for Ergo Z230

Reviews:

Related manuals for Ergo Z230

Brands by name

Popular brands