Jolly Mec FOGHEA, Installation, Use And Maintenance Card

Page: 22 / 48

1.9 Advice and warnings
When purchasing firewood, it is advisable to vary the sizes;
a length of 30/32 cm is ideal for quick lighting, and long
burn times, if the quality of the wood is good; efficiency and
functionality will also be optimum.
If the glass becomes very dirty (blackening) during operation
with pellets, the causes may be:
• Poor flue draught (clean the flue, or check its characteristics)
• Insufficient combustion air (increase the air by means of the
combustion fan)
• Non-use of the second door (optional)
• The quantity of pellets entering the burn pot (this depends on the
type of pellets used) is different from that given in the technical
data (par. 1.3). Check the hourly pellet consumption at medium
power and adjust the delivery by means of the feed control.
In the case of ignition with quantity of pellets greater than that
indicated on
chap. 1.8
, contact the Technical Assistance
Service.
To obtain a heating power of 23.2 kW, it is necessary to burn
5-6 kg of wood or 4-5 kg of pellets per hour.
Never light the fireplace, in particular in wood mode, without the
power supply connected.
If pellets have not been used for a long time (spring-summer),
the hopper, in feed screw and burn pot must be completely
emptied with the aid of a vacuum cleaner, then clean thoroughly
to prevent residual pellets from forming a lump and damaging
The hot air fan must be activated with the stove lit, as the “FOGHET” is a very powerful heat exchanger stove. The fan switches on
automatically only when the air temperature is approx. 40° C. If the electronic controller is switched off, the fan is automatically activated
when 120°C is reached, to prevent dangerous overheating. Therefore, NEVER OPERATE THE FIREPLACE/STOVE WITHOUT THE
POWER CONNECTED.
some parts at the next lighting.
Only use recommended fuels, otherwise the warranty will be
invalidated.
Every 5-10 qtl of pellets loaded in the hopper, check and remove
any sawdust deposited on the bottom. (sawdust reduces in feed
screw capacity and creates stove operation problems).
The firebox must always be closed, except when loading fuel,
to prevent smoke escaping
Check for any obstructions in the flue and the outside air inlets
before lighting the stove after a long period of disuse
Do not use the stove as an incinerator. Only use recommended
fuels.
The firebox cannot be modified; any unauthorised modification
automatically invalidates the warranty and relieves the
Manufacture of any liability
Do not place the stove in direct contact with combustible
materials; the minimum distance to be respected is 20 cm.
Regular and methodical maintenance is all-important for correct
operation and maximum efficiency.
This is a hight performance insert obtained by closed doors. In
case of opening and no perfect draftl conditions in the chimney
(12Pa), there could be smoke puff exit. In case you need to
charge wood remember to oper the damper control to avoid it
and to reposition the damper after the operation.
WARNING!
In case of a power failure or voltage rushes, some
electrical components could be damaged if the
fireplace is on and loaded with lots of wood. In case of
a power failure, to reduce the heat close the damper,
Caldo Control and the shutter on the ash pan; if it is still
too high, remove a few pieces of wood. The combustion
fan must be cleaned at least once a year. Only use
original replacement parts; original replacement parts
are available from authorised dealers and Assistance
Centres, or directly from JOLLY-MEC.
WARNING!
DO NOT TOUCH any parts of the firebox not covered by
the cladding, except the handles and controls, as they
can become very hot.
The room where the stove is installed must not
communicate directly with stair wells; no other boilers,
flues, stoves, fireplaces or air extractors must be in the
same room (excluded of the type “C” according to UNI
10683).
Ensure an outside air inlet of Ø 150 mm in the room,
connected to the stove.
MORE CLEANING = MORE EFFICIENCY
22