manualshive.com logo in svg

Johnson Controls IQ Panel 4, Installation Manual, Page: 163 / 178

Share
Download
Johnson Controls IQ Panel 4 Installation Manual Download Page 163

LEGAL

UL/cUL RESIDENTIAL FIRE & BURGLARY INSTALLATIONS

This product has been tested and found in compliance with the following standards:  UL1023 Household Burglar-Alarm 
System Units, UL985 Household Fire Warning System Units, ULC-S545 Residential Fire Warning Systems Control Units 
and ULC-S304 Security Level I Control Units, Accessories and Receiving Equipment for Intrusion Alarm Systems.  For ULC 
Installations refer to the Standard for the Installation of Residential Fire Warning Systems, CAN/ULC-S540: 

- Use only the compatible power supply referenced in this Installation Manual. 24 h standby power must be provided for 

fire applications and 4h for burglary only applications (AC trouble must be transmitted to SRC within 60 minutes). 

- Priority of signals on the Panel is set as Fire, CO, Burg, Panic, Aux and then Flood. 
- Use at least one compatible listed Smoke Detector for Fire Installations. 
- The entry delay shall not exceed 45 sec (UL) and 180 sec (ULC Security Level 1). 
- The exit delay shall not exceed 120 seconds (UL). 
- The control panel supports the Temporal 3 pattern for fire alarm notification 
- Test transmission cycle shall be set for 7 days transmission for Residential Fire applications, or 30 days for Residential 

Burglary only applications. 

- If Wireless Repeater is required to be employed with a RF Smoke Detectors or CO Detectors, two repeaters must be 

installed to cover EACH Smoke Detector and/or EACH CO detector. 

QOLSYS CONFIDENTIAL AND PROPRIETARY 

PAGE 

 OF 

163

178

Summary of Contents for IQ Panel 4



















































































































































































Reviews:

No comments