John Bean JLT4500S Manual Download Page 56

Page: 56 / 71

REV 02 OCT 2020 JLT4500-IOM-F

ATTENTION

Replace all worn or broken parts with genuine JohnBean parts. Contact your local Snap-on parts distributor for pricing and

availability. Call JohnBean. at

+39 0522/733-411

for the distributor in your area.

10 SAFETY PICTOGRAMS ON THE LIFT

For your safety, and the safety of others, read and understand all of the safety notices and decals included here.

WARNING

The user of the lift must be a person able to fully understand and recognize all the pictograms installed on it. The safety stickers

shall not be taken away, damaged or destroyed.

The owner of the lift and/or the person in charge of it shall immediately replace any damaged or partially unreadable pictogram.

Safety decals similar to those shown here are found on a properly installed lift. Be sure that all safety decals have been correctly installed on

the Power Unit reservoir / main column. Verify that all authorized operators know the location of these decals and fully understand their

meaning. Replace worn, faded, or damaged decals promptly.

Summary of Contents for JLT4500S








































































Search results

Summary of Contents for JLT4500S

Reviews:

Related manuals for JLT4500S

Brands by name

Popular brands

John Bean JLT4500S, Manual

Search results

Summary of Contents for JLT4500S

Reviews:

Related manuals for JLT4500S

Brands by name

Popular brands