John Bean JLT4500S Manual Download Page 42

Page: 42 / 71

REV 02 OCT 2020 JLT4500-IOM-F

5.6.3 HYDRAULIC OIL RECOMMENDED.

Here equivalents hydraulic oils recommend by

JohnBean

for the use with the

JLT4500

type are listed:

If any of the above-mentioned oils are available, use oil with a viscosity of 46 cst at 40°according to the ISO6743-4-ISO VG 46 norm. (Alternate

Hydraulic oil according to ISO32 can be substituted)

MANUFACTURER

DESCRIPTION

Aral

Vitam GF 46

HLP 46

Esso

Nuto H 46

Esso

Hydraulioil 46

Fina

Hydran 46

Klockner

Rando oil HDA 46

Raab karcher

Aval Vitamin GF 46

ATTENTION

Eventually particular rigid ambient temperatures – below 10°C – could result in slower lowering/lifting speeds.

This is not to be considered a defect of the lift; the extent of the effects of a low ambient temperature could be reduced by using a

lower viscosity oil. Contact JohnBean technical assistance to get information on the most suitable type of oil to be used.

DANGER

The complete change of all the hydraulic oil and the cleaning of the tank are strongly advised every 5 years or after every 500 days

of use. The exhausted oil will have to be scraped according to the locally enforced laws.

5.6.4 CLEANING:

For the proper conservation of the system, provide for the regular cleaning of the lift by removing all the dust and/or parts of cloth lost

while working. When cleaning, use non-corrosive and non-pollutant detergents that do not react with the paints used on the lift. Use

compressed air to clean the power unit.

DANGER

Clean up the lift after every working session, removing all the impurities that could, with the time, being cause of malfunctions and

dangers. If during the work there were liquids lost from the car that was being repaired, dry up the lift as soon as possible.

Summary of Contents for JLT4500S








































































Search results

Summary of Contents for JLT4500S

Reviews:

Related manuals for JLT4500S

Brands by name

Popular brands

John Bean JLT4500S, Manual

Search results

Summary of Contents for JLT4500S

Reviews:

Related manuals for JLT4500S

Brands by name

Popular brands