4-8
n
Jenn-Air Built-in Coffee System
COMPONENT ACCESS
9
3.
Press SIZE to select the size of the coffee cup: espresso,
small cup, medium cup, large cup or mug.
4.
Press 1 COFFEE to make 1 cup of coffee or 2 COFFEE to
make 2 cups of coffee.
5.
The coffee system will grind the coffee beans and dispense
the coffee. After the preset quantity of coffee has been
dispensed, the coffee system will automatically stop and
empty the coffee grounds into the grounds container.
NOTE:
The coffee system can be interrupted at any time by
pressing the 1 Coffee or 2 Coffee button again.
6.
After a few seconds, the coffee system will be ready for use
again.
7.
To switch off the coffee system, press the On/Standby
button. The coffee system will run an automatic rinse cycle
and then go into standby mode.
If the coffee runoff is too slow or incomplete, or if the runoff is too
quick and the coffee is not creamy enough, see the “Adjusting
the Coffee Grinder” section.
Do not remove the water tank during the coffee runoff. If the water
tank is removed, the coffee system cannot make coffee and will
display “FILL TANK!” Check the water level in the tank and replace
it. To restart the coffee system, press OK. “HOT WATER Press
OK” will be displayed. Press OK. Water will run off from the spout
for approximately 30 seconds. After the runoff completes, the
coffee system will return to the programmed standard settings.
The coffee system may require you to repeat the operation
several times to eliminate any air in the water line.
Tips for Hotter Coffee:
■
Run a Rinse cycle before brewing coffee. See “Rinsing” in the
“Settings” section.
■
Do not use very thick cups as they will absorb the heat unless
preheated.
■
Preheat all cups by rinsing them with hot water. See “Rinsing”
in the “Settings” section.
To Clean:
After every 14 cups of coffee made, the drip tray needs to be
cleaned and the coffee grounds container emptied.
1.
Open the service door on the front by pulling the coffee
spout.
2.
Remove the drip tray and clean it.
NOTE:
When cleaning the coffee system, always fully remove
the drip tray.
3.
Empty the coffee grounds container and replace it.
NOTE:
Every time the drip tray is removed, the coffee
grounds container must be emptied. Failure to do so may
clog the coffee system.
4.
Replace the drip tray and close the service door.
Changing the Amount of Coffee
The coffee system is factory-set to automatically deliver
approximately the following amounts of coffee:
■
Espresso: 1 oz (30 mL)
■
Small cup: 1½ oz (45 mL)
■
Medium cup: 2 oz (60 mL)
■
Large cup: 3 oz (90 mL)
■
Mug: 4 oz (120 mL)
These settings can be adjusted up to 6 oz (180 mL).
NOTE:
The 2 Coffee button can be used to dispense twice as
much coffee as the 1 Coffee button even with custom settings. If
you wish to return to the original settings, see “Default Values” in
the “Settings” section.
1.
Press SIZE until the display shows the desired coffee size.
2.
Place your cup beneath the coffee spout. Press and hold
1 COFFEE until “PROGRAM QUANTITY” is displayed.
NOTE:
The coffee system will begin dispensing coffee before
“PROGRAM QUANTITY” is displayed.
3.
Press 1 COFFEE again to stop the runoff and save the
desired amount of coffee for the size.
The machine is now reprogrammed and ready for use.
A. Coffee spout
B. Service door
A
B
A. Coffee grounds container
B. Drip tray
A
B
Before Disassembling the Coffee System
WARNING
Electrical Shock Hazard
Disconnect power before servicing.
Failure to do so can result in death or
electrical shock.
Replace all parts and panels before operating.
Preparation
Perform the following to prepare coffee system for
disassembly.
1.
Slide the coffee system forward using the handles as
shown in the following illustration.
2.
Press main on/off switch (A) on right side of coffee system
to turn off unit.
Front View:
Rear View:
A. Cup tray
B. Service door
C. Coffee feed
D. Coffee grounds container
E. Brewing unit
F. On/standby button
G. Cup tray lights
H. Control panel
I. Hot water and steam nozzle
J. Water tank
K. Coffee spout (height-adjustable)
L. Drip tray
A. Main on/off switch
B. Grinding coarseness adjustment knob
C. Coffee bean container
D. Coffee bean container lid
E. Ground coffee funnel cap
G. Scoop compartment
F. Scoop
H. Ground coffee funnel feed
I. Power supply cable
J. Terminal board
K. Storage tray
A
B
C
D
E
G
H
I
J
K
F
L
A
3.
Unplug coffee system or disconnect power.
4.
Remove power cord from power cord clip in cabinet.
5.
Remove all items from right and left storage trays (“B”
in previous illustration), e.g., bags of coffee beans,
containers of ground coffee, sugar, creamer, etc.
6.
If installed, remove hot water spout or milk container.
7.
Remove water tank (“B” in following illustration).
8.
Open service door (D) and remove drip tray (C) with
coffee grounds container (A).
9.
Remove the four 4.2 x 9.5 mm screws (C) securing
the coffee system to the runners. Refer to following
illustration.
5
Install the Coffee System
1.
Pull the runners forward until they are fully extended and in
the locked position.
2.
Using 2 or more people, position the coffee system onto the
runners, making sure that the 4 pins of the L-brackets fit
securely inside the holes on the bottom of the coffee system.
3.
Place the level on top of the coffee system and check
levelness of the coffee system, first side to side; then front to
back.
4.
If the coffee system is not level: Using 2 or more people,
remove the coffee system from the runners. Add the
necessary leveling spacers over the pins to help level the
coffee system.
5.
Using 2 or more people, position the coffee system onto the
runners, making sure that the 4 pins of the L-brackets fit
securely inside the holes on the bottom of the coffee system.
6.
Check that the coffee system is level. If it is not level, repeat
steps 4 and 5. If it is level, secure the coffee system to the
L-brackets with the 4 screws.
7.
Position the power supply cord clip on the top of the cabinet,
approximately 14" (35.6 cm) from the front of the cabinet and
centered from left to right. With a pencil, mark the hole
through the clip on the top of the cabinet.
8.
Using a 2 mm drill, drill the hole marked in Step 7.
9.
Using 1 screw, attach the power supply cord clip to the top of
the cabinet.
A. Pins
WARNING
Excessive Weight Hazard
Use two or more people to move and install the built-in
coffee system.
Failure to do so can result in back or other injury.
A
A. Leveling spacers
B. Pins
C. Screws
A. Power supply cord clip
B. Power supply cord
B
C
A
approx. 14"
(35.6 cm)
A
B
10.
Remove the coffee system from the runners and relocate
to an appropriate work surface.
A. Main On/Off Switch
B. Storage Tray
A. Coffee grounds container
C. Drip Tray
B. Water Tank
D. Service Door
C
B
D
A
B
6
6.
“TURNING OFF Please wait...” will be displayed. The coffee
system will turn off.
7.
Slide the coffee system forward using the handles as shown
in the following illustration.
8.
Open the coffee bean container lid, fill the coffee bean
container with coffee beans and close the lid.
IMPORTANT
: Do not place ground coffee, freeze-dried
coffee, caramelized coffee or foreign objects into the coffee
bean container, as they could damage the machine.
9.
Push the coffee system back into the housing. It is now ready
for normal use.
NOTE:
When first using the coffee system, you need to make 4-5
cups of coffee and 4-5 cappuccinos before the coffee system
gives good results.
NOTE:
Each time the machine is turned on using the main On/Off
switch, it runs a self-diagnosis function and then goes into
standby mode. To turn the machine on again, press the On/
Standby button to the left of the coffee spout. See the illustration
in the “Parts and Features” section.
COFFEE SYSTEM USE
Settings
You can control several settings through the Settings Menu:
Rinsing, Beep, Statistics, Default Values, Water Hardness,
Auto-Off, Coffee Temperature, Descaling, Auto-Start, Language
and Adjust Time.
To access the Settings Menu, press MENU. To exit the Settings
Menu, press MENU again.
Rinsing
This function is used to rinse the coffee spout or preheat the
brewing unit if more than 2 minutes have passed since the
machine was last preheated. Hot water from the rinse cycle can
be used to preheat a small cup of coffee.
1.
Press MENU.
2.
Press the up and down arrow keys until “RINSING” is
displayed. Press OK.
3.
“OK to confirm” will be displayed. Press OK.
4.
“Please wait...” and a progress bar will be displayed. 1 oz
(30 mL) of hot water will run into the drip tray.
NOTE:
If desired, you can place a small cup beneath the
coffee spout. The hot water will warm the cup. Empty the hot
water before using the cup for coffee.
Beep
The coffee system is factory-set with tones enabled, but they can
be disabled.
1.
Press MENU.
2.
Press the up and down arrow keys until “BEEP Enabled” is
displayed. Press OK.
3.
“BEEP Disable?” will be displayed. Press OK to deactivate the
tones.
4.
Press MENU to exit the menu.
To reactivate the tones, repeat steps 1-4.
Statistics
This function allows you to view the machine statistics.
1.
Press MENU.
2.
Press the up and down arrow keys until “STATISTICS” is
displayed. Press OK.
A. Handles
A
A
A. Coffee bean container
A
A. 1 Coffee
B. 2 Coffee
C. Menu
D. Strength
E. Display
F. Down arrow key
G. Up arrow key
H. Hot water
I. Cappuccino
J. OK
K. Size
A
B
C
D
E
G
H
I
J
K
F
