JDS Uniphase SmartClass E1 User Manual Download | Manualshive

Page: 142 / 144

background image

Appendix B

Specifications

Warranty information

126

SmartClass E1 Tester User’s Guide

party or (b) all or any part of the Software is installed on any computer
equipment other than the Designated Server or used with any operating
system for which the Software is not designed.

WARRANTY DISCLAIMER —

FOR HARDWARE, AND/OR SOFTWARE

FURNISHED BY JDSU, THE FOREGOING WARRANTIES ARE IN LIEU OF
ALL OTHER WARRANTEES AND CONDITIONS, EXPRESS OR IMPLIED.
JDSU SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES, EITHER
EXPRESS OR IMPLIED, ON ANY HARDWARE, SOFTWARE, DOCUMEN-
TATION OR SERVICES INCLUDING BUT NOT LIMITED TO WARRANTIES
RELATING TO QUALITY, PERFORMANCE, NONINFRINGEMENT,
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AS
WELL AS THOSE ARISING FROM ANY COURSE OF DEALING, USAGE OR
TRADE PRACTICE. UNDER NO CIRCUMSTANCES WILL JDSU BE LIABLE
FOR ANY INDIRECT OR CONSEQUENTIAL DAMAGES RELATED TO
BREACH OF THIS WARRANTY.

«
...
140
141
142
143
144
»

Summary of Contents for SmartClass E1

















































































































































Reviews:

No comments

Related manuals for SmartClass E1

Brand: Taber Pages: 27

Brand: Odom Pages: 19

Brand: MacDon Pages: 30

Brand: Makita Pages: 60

Brand: JB-Lighting Pages: 60

Brand: Dawn Pages: 8

Brand: BACtrack Pages: 13

Brand: Badgematic Pages: 28

Brand: BACtrack Pages: 2

Brand: MADRIX Pages: 28

Brand: BACTcontrol Pages: 28

Brand: Backyard Products Pages: 98

Brand: Datavideo Pages: 28

Brand: NanoVibronix Pages: 2

Brand: NanoVibronix Pages: 32

Shapes Hexagons

Brand: Nanoleaf Pages: 27

Brand: Safavieh Pages: 2

Brand: Vendlet Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands