JCM GAMMA VERSUS Series Manual Download

Page: 25 / 111

GAMMA VERSUS MANUAL

COD. 1257066 Gamma VERSUS Manual v1.13

6. DISPLAY MESSAGES

6.1 Serious errors

Errors associated with the security of the installation or equipment malfunction. These errors must be
resolved always.



Error

Description

Solution



INT. ERROR

Internal error

Go to the technical service



HA ERROR

Hall A error

Verify the hall A input connections



PROG TIME MAX

Programming time maximum

Program a maneuver below the
maximum allowed time



S.EDGE.CL ERROR

Closing safety edge error

Verify the security edge band
connections when closing



S.EDGE.OP ERROR

Opening safety edge error

Verify the security edge band
connections when opening



TEMP ON

Motor temperature sensor
activated

Verify the motor state and the
temperature sensor connection



TEST.CL ERROR

Closing auto test error

Verify that the security device connected
to the security connection when closing
is in good conditions and correctly
installed



TEST.OP ERROR

Opening auto test error

Verify that the security device connected
to the security connection when opening
is in good conditions and correctly
installed



RSENS NC WHEN
PROG

Control panel programmed without
RSENS connected

Connect the RSEC card and program the
control panel again



RSENS NOT FOUND

Control panel programmed with
RSENS connected and now it is
not connected

Program the control panel again without
RSEC or connect the RSEC again that
was programmed to the control panel
previously



RSENS PROG ERROR

RSENS programming error, are R
and T paired?

Program the transmitter RSENS to the
RSEC receiver card



STOP

Control panel stopped by an STOP Verify that the STOP input has been

activated



INTERNAL ERROR

Internal control panel error

Go to the technical service



DOOR LOCKED RSENS Closed door latch

Open the door's latch before the opening
manoeuvre



RBAND NOT FOUND

Control panel programmed with
RBAND connected and now it is
not connected

Program the control panel again without
using RBAND or connect the RBAND
that was connected to the control panel
previously



RBAND NC WHEN
PROG

Control panel not programmed
with RBAND connected

Connect the RBAND card and program
the control panel again



FC NOT LEARNT

End of course learning error

Verify the intern motor limit switches



ERROR SYNC RSENS

Synchronization error between the
receiver and the transmitter

Program the transmitter RSENS to the
RSEC receiver card

Summary of Contents for GAMMA VERSUS Series
















































































































Search results

Summary of Contents for GAMMA VERSUS Series

Reviews:

Related manuals for GAMMA VERSUS Series

Brands by name

Popular brands

JCM GAMMA VERSUS Series, Manual

Search results

Summary of Contents for GAMMA VERSUS Series

Reviews:

Related manuals for GAMMA VERSUS Series

Brands by name

Popular brands