manualshive.com logo in svg

JCM GAMMA VERSUS Series, Manual

Share
Download
JCM GAMMA VERSUS Series Manual Download Page 103

GAMMA VERSUS MANUAL 

 

103

 

COD. 1257066                                                                                         Gamma VERSUS Manual v1.13 

 

 

 

6 - Disconnect the Updator form the PC and proceed to update the device. If you downloaded the firmware on 
the updating memory card, when you insert the card into the device and feed it, the device will be updated 

with the new firmware. If it is a firmware update for a control panel, follow the instructions shown in the 

chapter "Upgrading VERSUS Control Panels." 
 

 
UPGRADING VERSUS CONTROL PANELS 

To update the firmware of the control panel with the version loaded on the Updator, connect the Updator through an 
Ethernet cable to the control panel via the RJ45 connector. 

UNPLUG POWER SUPPLY               CONNECT UPDATOR                      PLUG POWER SUPPLY                    LED’S FLASHES                                                                         

   

  

   

 

WAIT 10S 

 UPGRADING OK     

      

     

 
UPGRADING VERSUS-PROG PORTABLE PROGRAMMER 

To download the latest version of firmware on a handheld programmer, connect the Versus-Prog through a USB cable 
(Type A - Mini B) to your PC and follow the prompts.  

 

1 - Run the software "Firmware update tool" from the PC.  
 

2 - On the main screen select, on the "Device Selection" option, the Versus-Prog device.  

 

 
 

 

 
 

 

 

 

3 - Press the button "Connect to Versus Prog" and if the connection is correct, at the bottom of the window you 

will see "Device Serial: Prog Versus connected". 

 
 

 

 
 

 

 
 

 

Note: It is important to remember that when the firmware upgrading is done, 
the control panel will lose all the settings stored before and will return to the 
factory values by default. 

 

Summary of Contents for GAMMA VERSUS Series
















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands