manualshive.com logo in svg

JCM GAMMA VERSUS Series, Manual

Share
Download
JCM GAMMA VERSUS Series Manual Download Page 89

GAMMA VERSUS MANUAL 

 

89

 

COD. 1257066                                                                                         Gamma VERSUS Manual v1.13 

 

 

10.4 V-EXPAND card 

 

DESCRIPTION 

Expansion card with inputs and outputs and/or functions. Each card has two card connectors. Multiple cards may be 
connected in series. 
It also has an additional power supply 230Vac, to increase the possible consumption of the cards, or to 
feed externally and operate autonomously. 
 

INSTALLATION 

A)

 

Installation in boxes with dimensions 285x225x92mm. 

1.OPEN BOX 

 

2.PLACE CARD 

 

3. SCREW CARD  

 

4.CONNECT CARD 

 

 

B)

 

Installation in additional small box with dimensions 180x152x88mm.  

1.PLACE IN 
ADDITIONAL CARD 

 

2.CONNECT CONTROL  
PANEL 

 

 

 

 

USE OF THE SYSTEM 

This equipment is designed to be installed with control panels for door and gate installations. It is not guaranteed 

for directly activating equipment other than that specified. 
The manufacturer reserves the right to change the specification of the equipment without prior warning. 

 

IMPORTANT ANNEX 

Disconnect the power supply whenever you proceed to the installation or repair of the control panel. 

In accordance with the European low voltage directive, you are informed of the following requirements: 
· For permanently connected equipment, an easily accessible connection device must be incorporated into the 

cabling. 

· This system must only be installed by a qualified person that has experience with automatic doors/gates and 

knowledge of the relevant EU standards. 
· The instructions for use of this equipment must always remain in the possession of the user. 

· Terminals with a maximum section of 3.8mm2 must be used to connect the cables. 

· The frequency of the RadioBand system does not interfere in any way with the 868 MHz remote control systems. 

 

 

 

Summary of Contents for GAMMA VERSUS Series
















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands