manualshive.com logo in svg

JCM GAMMA VERSUS Series, Manual

Share
Download
JCM GAMMA VERSUS Series Manual Download Page 86

GAMMA VERSUS MANUAL 

 

86

 

COD. 1257066                                                                                         Gamma VERSUS Manual v1.13 

 

 

10.3 V-DPLAY card 

 

DESCRIPTION 

Display card for manage and program the programmable parameters of the control panel. 

 

CONNECTION 

Connect the card to the control panel on the indicated terminals. The control panel must be without power supply. 
Note: In case of installation with the box upside, turn up the card and then the frontal buttons will be reconfigured to 
the new position of the control panel. 

 

OPERATING 

 

1. STANDBY 

MODE 

 

 

2.  DOOR STATE INDICATION MODE 

 

DOOR OPENED  

         DOOR CLOSED                       DOOR OPENING                    DOOR CLOSING 

   

   

   

 

ERROR                                     ERROR NUMBER 

    

 

 
 
 

 

 

When the door is in movement, the control panel indicates the state of the 
door: opened, closed or moving.  

You also can access to visualize the state of the door pressing any of the 
buttons of the display card during 2 seconds. The display will indicate the 
state of the door. The control panel will get out this mode automatically after 
30 seconds. 

It is only available to enter standby mode 
if the door is not in movement and if 
there is no error activated.

 

 

Summary of Contents for GAMMA VERSUS Series
















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands