Japan Tiger Fast Ethernet 7100e+, User Manual

Page: 142 / 160

Fast Ethernet
7100e +
142
Setup Value
ENABLE : To use the
function
DISABLE: Not to use
the function
Default value
None
Default value
None
Default value
All None
Default value
10 sec.
ENABLE : To use the
function
DISABLE: Not to use
the function
Default value
" " (None)
Items
Bindery mode
NDS tree
NDS context
Remote Printer
PSERVER name1-8
JOB timeout
EtherTalk
EtherTalk protocol
Zone name
Function
In Print Server mode,. when controlling only
with NW4.1 NDS Mode, set Bindery Mode as
[Disable]. When connecting via NW4.1 Bindery
Service and NW3.1, always set Bindery Mode
as [ENABLE]
In Print Server Mode, enter NDS Tree Name.
The File Server, where NetWare Print Server is
attached, belongs to this NDS tree.
In Print Server Mode, enter the Context Name,
with which the Print Server was created.
Enter Print Server Name to be attached in
Print Server Mode. 8 print servers may be
designated at max. The value should be a
maximum of 31 characters or numbers.
This is the time from receiving the last print
packet to relieving the Ethernet Board port at
the end of the print job, in the Remote Printer
Mode. When the set value is too short, the
packet delay may make the printing stop on the
way. Normally, please use the printer with the
default value. The value may vary from 4 to
255 seconds.
Set whether EtherTalk protocol is used.
Enter EtherTalk zone name is required.
Function
For NetWare4.1, it is "Printer Name" of "Print Server
Information" in PCONSOLE.
For NetWare3.1, it is "Printer Configuration" name found
in "Print Server Configuration" of "Print Server
Information" in PCONSOLE.
This name is used only for NetWare. The value should
be a maximum of 31 alphanumerics characters.
It is Printer Name used only for EtherTalk protocol. The
value should bea maximum of 31 alphanumeric
characters.
Designate the character string transmitted to Printer
before outputting directly to the output port (lp port). Set
it when submitting such as control code before printing is
required. The value should be in 31 or shorter alphabets
or numbers. The special codes below may be assigned.
\ b ASCII Back-space, code 0x08
\ t ASCII Tab, code 0x09
\ n ASCII Return, code 0x0a
\ v ASCII Vertical tab, code 0x0b
\ f ASCII Page down, code 0x0c
\ r ASCII Esc code 0x0d
\ xnn HEX code expressed as nn
\ " " code 0x22
\\ \ code 0x5c
Designate the character string transmitted to Printer after
outputting directly to the output port (lp port). Set it when
submitting such as control code after printing is required.
The value should be a maximum of 31 alphanumeric
characters. The special codes are the same for BOJ
string.
Designate the character string transmitted to Printer
before outputting to the output port via KANJI
filter(euc,sjis port). Set it when submitting such as control
code before printing is required. The value should be a
maximum of 31 alphanumeric characters. The special
codes are the same for BOJ string.
Designate the character string transmitted to Printer after
outputting to the output port via KANJI filter(euc,sjis port).
Set it when submitting such as control code after printing
is required. The value should bea maximum of 31
alphanumeric characters. The special codes are the
same for BOJ string.
Setup Value
Default value
"ML"+"last 6 digits of MAC
Address" + "-prn1"
Default value
"ML"+"last 6 digits of MAC
Address"
Default value
" " (None)
Default value
" " (None)
Default value
" " (None)
Default value
¥x04
Items
Printer Port
NetWare port name
EtherTalk port name
BOJ string
EOJ string
BOJ string(KANJI)
EOJ string(KANJI)
7100e+.p65 25/08/99, 20:55 PM 142