PLEASE READ THE INSTRUCTIONS CARE-
FULLY BEFORE INSTALLING
Make sure that preparations that have been made comply
with the instructions given on the technical pre-installation
card enclosed.
Please ensure that you thoroughly check the product upon
receipt since we cannot accept responsibility for any dam-
age reported after installation. Should you find any dam-
age, please immediately notify the forwarder.
The guarantee is not valid after installation in the event of
damage caused by blows or abrasion.
Info
I
Check that the clamps holding the rubber couplings and
the air lines are tightly fastened.
I
Installation of the tub must take place with the wall finished
(already covered). The floor may also be finished, except for the
area for the siphon, as shown in
i
A
and
A1.
I
The finishing panels provided (to be installed on the long
front side and also on the back, on mod. 180x90) ensure ad-
equate ventilation, which is necessary for the air-water mix-
ture during the whirlpool use, while also allowing access to
the electromechanical parts under the tub.
Jacuzzi
®
panels ensure that it is possible to inspect the
devices installed under the tub for any maintenance which
may be required. It is therefore not advisable to perform re-
cessed installation or to use other panelling systems.
NOTE for mod. 180x90:
If the tub is installed with the back
against the wall, it is more difficult to access devices located un-
der the back, even if access is not completely prevented.
I
In areas of very hard water it is advisable to install a water sof-
tener, to avoid and/or reduce the formation of lime scale on the
panels and accessories of the tub.
Preparations
I
As soon as the tub has been placed in the installation loca-
tion, it is advisable to charge the remote control immediately, as
it requires 3 hours of uninterrupted charging before it can be
used (see chapter on "Electrical connection and charging the re-
mote control”).
Assembling the taps and fittings
I
Take the box that holds the various components of the taps
and fittings.
NOTE: assembly of the taps and fittings must be done with
the tub outside of the corner of installation and before it is
fastened to the floor.
I
(
i
1
) (1) Unscrew the headless screw. Slide out the cylin-
der of the tub filler(2); (3)
then tighten ring nut “A” and ring nut
“B”, and afterwards install the gasket “C”.
I
(
i
2
) From
under the tub edge, insert the cylinder in the in-
dicated hole and tighten the coupling from above with the o-rings.
NOTE: keep the headless screw for the subsequent fastening.
I
(
i
3
)
(1) By means of the coupling and the ring nut (2),
tem-
porarily
fasten the cylinder, ensuring that it is parallel with the
tub edge (3).
I
(
i
4
)
Install on a tap the same units used for the cross cylin-
der. Repeat the operation for the other tap.
NOTE:
it is preferable to install the ring nut with the faston on the
outermost tap (A)
(
i
6
).
I
(
i
5
)
From under the tub edge, insert the taps in the indi-
cated holes and tighten from above the ring nuts with the o-rings
I
(
i
6
)
By means of the respective ring nuts (from above and
below the tub edge), temporarily fasten the taps, turning one with
respect to the other, so as to make it easier to install the flexi-
ble hoses (3).
I
(
i
7
)
(1) Apply the square covers, as shown (2). After check-
ing that they are aligned with the tub edge, fasten them from
above with the ring nuts (3).
I
(
i
8
)
Install the shower support by inserting the indicated
gasket. Then apply the square cover.
I
(
i
9
)
From beneath the tub edge, apply another gasket and
attach it with the indicated nut.
I
(
i
10
)
Take shower hose (fittings 1/2”-3/8”) and insert
them in the following components (from the side of the 3/8” fit-
ting):
push button K - ring nut L - spacer M - square cover N - threaded
tube P - Teflon washer Q
(internal ø 23.3 mm)
- threaded tube R
- spring S - Teflon washer T
(internal ø 26 mm)
- gasket U
(the
brass part must face downwards).
I
(
i
11
) Fasten the flexible hose of 1/2” M-F (provided)
to the cross cylinder and run it through the inside of the
shower support, placing it over the tub edge.
I
(
i
12
)
(1) From above the tub edge, connect the shower
hose to the hose you just installed, placing the gasket. (2) Line
up washer T and gasket U inside the shower support.
I
(
i
13
)
Screw the threaded tube R all the way into the show-
er support.
I
(
i
14
)
(1) Tighten washer Q onto threaded tube P and
place the latter on spring S inside the threaded tube R (2).
I
(
i
15
)
(1) Place the spacer M over the square cover N; (2)
then screw the ring nut L onto the threaded tube P and then
screw push button L onto the threaded tube R (3).
I
(
i
16
)
Run the flexible hose under the tub edge and screw in the
shower head, placing the gasket.
7
Summary of Contents for J-Sha Mi
