IWAKI PUMPS EHN-B11-NAE Manual Download

Page: 11 / 68

fet

y i

nst

cti

• The pump has a rating of IP65, but is not waterproof. Do not operate the

pump while wet with solution or water. Failure or injury may result. Immedi-
ately dry off the pump if it gets wet.

• Do not close discharge line during operation. Solution may leak or tub-

ing may break. Install a relief valve to ensure safety and prevent damaged
plumbing.

• Do not remove the control unit. Note that an applicable control unit differs

with each drive unit. Do not attach a control unit to a different drive unit.
Otherwise, an electrical circuit or the drive unit may fail.

• Solution in the discharge line may be under pressure. Release the pres-

sure from the discharge line before disconnecting plumbing or disassembly
of the pump to avoid solution spray.

• Wear protective clothing when handling or working with pumps. Consult

solution MSDS for appropriate precautions. Do not come into contact with
residual solution.

• Do not clean the pump or nameplate with a solvent such as benzine and

thinner. This may discolour the pump or erase printing. Use a dry or a
damp cloth or a neutral detergent.

Precautions for use

Caution

Requirement

Benzine

Thinner

Caution

Summary of Contents for EHN-B11-NAE





































































Search results

Summary of Contents for EHN-B11-NAE

Reviews:

Related manuals for EHN-B11-NAE

Brands by name

Popular brands

IWAKI PUMPS EHN-B11-NAE, Manual

Search results

Summary of Contents for EHN-B11-NAE

Reviews:

Related manuals for EHN-B11-NAE

Brands by name

Popular brands