IWAKI PUMPS EHN-B11-NAE Manual Download

Page: 51 / 68

aint

ena
nc

Before replacement

First release pressure from the pump head and discharge line.

Stop the pump operation.

Rotate the adjusting screw two revolutions anticlockwies or open an air vent line to re-

lease pressure.

NOTE

Do not rotate the screw three revolutions from the closed position. The adjusting screw may come off
with solution spray.

Check the air vent line and the pump head are depressurized.

Liquid pressure is released from the air vent line in the form of solution spray.

NOTE

If pressurized liquid is not expelled, run the pump with an opened air vent line until pressure is re-
moved.

Valve set replacement

■ Discharge valve set disassembly/assembly

Necessary tools

• An adjustable wrench or spanner

• A 21mm box wrench

• A pair of tweezers

*Unfix the pump base before disassembly.

Loosen the fitting nut and remove the discharge tube

and air bleed tube.

Turn the lock nut anticlockwise by an adjustable wrench

and remove the air vent body A.

Wear part replacement

Lock nut

Air vent

body A

Fitting nut

Air bleed tube

Discharge tube

Summary of Contents for EHN-B11-NAE





































































Search results

Summary of Contents for EHN-B11-NAE

Reviews:

Related manuals for EHN-B11-NAE

Brands by name

Popular brands

IWAKI PUMPS EHN-B11-NAE, Manual

Search results

Summary of Contents for EHN-B11-NAE

Reviews:

Related manuals for EHN-B11-NAE

Brands by name

Popular brands