IWAKI PUMPS EHN-B11-NAE Manual Download | Manualshive

Page: 32 / 68

background image

32

Before operation

Degassing

The gas in the pump and tubing is the obstacle to liquid delivery and needs to be expelled before the pump is

started. Especially:

• When the pump starts to run for the first time.
• When a flow rate is too low.
• After liquid is replaced in a supply tank.
• After a long period of stoppage
• After maintenance and inspection are performed

NOTE
• Both gas and chemical come out together through an air bleed tube. Place the end of the tube in a supply

tank or a container.

• Some chemicals may damage skin and dry end parts. Wash/wipe chemicals off immediately if they got wet.

Points to be checked

• An air bleed tube is connected to the pump.

Turn on power.

The ON LED and the display are turned on.

*

The pump waits in the manual mode when turned on with the factory default setting.

Set stroke rate to 360spm.

• spm increases/decreases every time the UP/DOWN key is pushed.
• Press and hold either key for more than three seconds for quick change. Quick change stops at 1 or

360spm. 1 or 360rpm skips to 360 or 1spm when the key is released and pushed once.

2

1

Air bleed tube

«
...
30
31
32
33
34
...
»

Summary of Contents for EHN-B11-NAE





































































Reviews:

No comments

Related manuals for EHN-B11-NAE

Brand: A.O. Smith Pages: 56

Brand: Davey Pages: 12

Brand: Barmesa Pumps Pages: 42

Brand: Gardena Pages: 11

Brand: Wanner Engineering Pages: 16

Brand: Eaton Pages: 20

Brand: Eaton Pages: 21

Brand: SAER Elettropompe Pages: 76

Brand: Lamborghini Caloreclima Pages: 192

607 challenger series

Brand: National Vacuum Equipment Pages: 20

Hydro-Guard HG-3

Brand: Mueller Pages: 7

Brand: SGS Pages: 10

DHH 12 Si control

Brand: STIEBEL ELTRON Pages: 168

Brand: Kärcher Pages: 68

Brand: salmson Pages: 36

Brand: Rheem Pages: 16

Brand: Laars Pages: 20

Cylinder DuroTech MAP07

Brand: Milwaukee Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands