IWAKI PUMPS EHN-B11-NAE Manual Download

Page: 27 / 68

stal

lat

ion

Wiring

Wiring

Wiring for power voltage, earthing and external signals.

Points to be observed

Observe the following points during wiring work.
•

Electrical work should be performed by a qualified electrician. Always observe local

electric codes.

•

Observe the rated voltage range, or the electrical circuit in the control unit may fail.

•

Do not perform wiring work while electric power is ON. Otherwise, an electrical shock or

a short circuit may result. Be sure to turn off the power before wiring work.

•

Be careful for electric power not to be turned on during work.

Necessary tools

• Adjustable wrench or spanner

• Phillips screw driver

• Precision screw driver

Power voltage/Earthing

Points to be checked

• Check that power voltage is turned off.

Connect power cable via crimp contacts.

Earth the pump.

NOTE
• Do not share a power source with a high power device which may generate a surge voltage. Otherwise an

electronic circuit may fail. The conductive noise caused by an inverter also affects the circuit.

• Energize the pump with a power voltage via a mechanical relay or switch. Do not fluctuate the voltage, or

CPU may malfunction. See page 28 for the precautions for ON-OFF control by a mechanical relay.

Apply power sharply

Do not apply gradually

• Use a circuit protector (250VAC, 3A Medium speed) as necessary.
• Do not use a motor thermal relay.

POWER

OFF

TIME

POWER

OFF

TIME

Summary of Contents for EHN-B11-NAE





































































Search results

Summary of Contents for EHN-B11-NAE

Reviews:

Related manuals for EHN-B11-NAE

Brands by name

Popular brands

IWAKI PUMPS EHN-B11-NAE, Manual

Search results

Summary of Contents for EHN-B11-NAE

Reviews:

Related manuals for EHN-B11-NAE

Brands by name

Popular brands