IWAKI PUMPS EHN-B11-NAE Manual Download | Manualshive

Page: 29 / 68

background image

29

In

stal

lat

ion

Wiring

NOTE
• Do not lay on these signal cables in parallel with a power cable. Otherwise the electromagnetic induction

noise is generated and malfunction or failure may result.

• The following products are the recommended SSRs (Solid State Relays) for signal input. Any other SSRs

might cause malfunction. See manufacturer's information for details on these SSRs.

–OMRON G3FD-102S or G3FD-102SN
–OMRON G3TA-IDZR02S or G3TA-IDZR02SM

• When using a mechanical relay for signal input, its minimum application load should be 5mA or below.
• Insert the DIN 4- or 5-pin female connector as far as it will go and then tighten the skirt to make a secure con-

nection.

*Use either a no-voltage contact or an open collector for the input, STOP, and AUX signals.
*Set pulse duration to 10-100ms and the number of pulses at or below 360 pulses per minute.

Detach the terminal case.

Remove four screws and take out the terminal case.

*

The gasket is provided to keep water-/dust-tightness between
the parts. Be sure to replace once it has removed.

Remove the power line and signal line terminal

blocks from the PCB in the control unit.

Remove a cable gland and a cap to pull out a cable gasket.

*

The cap is not used as long as a cable is connected.

Pass an external signal cable into the terminal

case via the cable gland and the cable gasket.

*

Be careful not to oppositely orient the cable gasket.

Cap

Cable gland

Cable gasket

Taper

Cable gland

Cable gasket

Signal-line

terminal block

Power-line

terminal block

2

1

3

4

Control unit

Case gasket

Terminal case
Tapping screw

«
...
27
28
29
30
31
...
»

Summary of Contents for EHN-B11-NAE





































































Reviews:

No comments

Related manuals for EHN-B11-NAE

Brand: Walchem Pages: 34

Brand: WAGNER Pages: 84

Brand: WAGNER Pages: 52

MiniTank WM-2.5

Brand: Waiwela Pages: 20

Brand: Dupla MARIN Pages: 28

ARO PP10A Series

Brand: Ingersoll-Rand Pages: 12

Brand: Navien Pages: 131

Brand: Calpeda Pages: 19

Brand: ABS Pages: 10

Brand: NAVAC Pages: 8

Brand: F.F. Group Pages: 28

Brand: Malmbergs Pages: 12

Brand: Clarke Pages: 12

Brand: Oasis Pages: 40

Brand: Fluke Pages: 2

Brand: sauermann Pages: 8

PILE DRIVER 84900

Brand: Lincoln Pages: 8

Brand: Williamson Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands