IWAKI PUMPS EHN-B11-NAE Manual Download | Manualshive

Page: 46 / 68

background image

46

Operation

Keypad lock

Keypad lock can be active for the prevention of erroneous key operation.

NOTE
Any key operation is not effective when keypads are locked. In an emergency, turn off the main power to stop

operation. Keypads are locked again when the pump is powered.

■ Keypad lock activation

Press and hold the start/stop key for 3 seconds.

The following displays will appear.

Manual operation

Digital control

3 sec

3 sec

■ Keypad lock release

Press and hold the start/stop key for 3 seconds to release a keypad lock.

Priming function

This key operation runs the pump at the maximum stroke rate in operation.

Press and hold both the UP and DOWN keys.

The pump runs at the maximum stroke rate while both the keys are pressed.

1

1

1

«
...
44
45
46
47
48
...
»

Summary of Contents for EHN-B11-NAE





































































Reviews:

No comments

Related manuals for EHN-B11-NAE

Brand: Waterous Pages: 36

Brand: Paragon Pages: 16

Brand: Danfoss Pages: 64

Brand: Danfoss Pages: 86

Brand: Danfoss Pages: 28

Clima Canal JDPC.002

Brand: Jaga Pages: 8

Brand: Patterson Pages: 16

Brand: PAPILLON Pages: 22

Brand: Walchem Pages: 34

Brand: WAGNER Pages: 84

Brand: WAGNER Pages: 52

MiniTank WM-2.5

Brand: Waiwela Pages: 20

Brand: Wilo Pages: 76

Brand: Pattfield Ergo Tools Pages: 162

Altherma 3 R MT F+W

Brand: Daikin Pages: 68

Brand: DAB Pages: 25

Brand: A.O. Smith Pages: 32

RIBILAND PRPVC1501V

Brand: Ribimex Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands