IWAKI PUMPS EHN-B11-NAE Manual Download | Manualshive

Page: 9 / 68

background image

9

Sa

fet

y i

nst

ru

cti

on

s

Do not use the pump in a wet location

The pump is not waterproof. Use of the pump in wet or extremely humid
locations could lead to electric shock or short circuit.

Grounding

Risk of electrical shock! Always properly ground the pump. Conform to lo-
cal electric codes.

Install a GFCI (earth leakage breaker)

An electrical failure of the pump may adversely affect other devices on the
same line. Purchase and install an earth leakage breaker separately.

Preventative maintenance

Follow instructions in this manual for replacement of wear parts. Do not
disassemble the pump beyond the extent of the instructions.

Do not use a damaged pump

Using a damaged pump could lead to an electric leak or shock.

Disposal of a used pump

Dispose of any used or damaged pump in accordance with local rules
and regulations. If necessary, consult a licensed industrial waste disposal
company.

Check the pump head bolts

Liquid may leak if any of pump head bolts become loose. Tighten the bolts
evenly to the specified torque below in diagonal order before initial opera-
tion and at regular intervals.

Tightening torque

EHN-B11/-B16/-B21/-C16/-C21 : 2.16 N•m
EHN-B31/-C31/-C36

: 2.55 N•m

Install a relief valve

Install a relief valve on a discharge line near the pump so as to automati-
cally release the discharge pressure when it exceeds the maximum level.

Requirement

Requirement

Caution

Electrical

shock

CAUTIONS

Requirement

Prohibited

Grounding

Prohibited

«
...
7
8
9
10
11
...
»

Summary of Contents for EHN-B11-NAE





































































Reviews:

No comments

Related manuals for EHN-B11-NAE

Brand: TANKLESS Pages: 72

Brand: Kaisai Pages: 40

Water Jet Lightning

Brand: Oase Pages: 28

AquaMax Eco Premium 4000

Brand: Oase Pages: 120

Brand: Oase Pages: 9

DOMINATOR Series

Brand: RBI Pages: 52

Brand: TATRA Pages: 16

FUTERA II Series

Brand: RBI Pages: 32

HydraPump Smart

Brand: Watershed Innovations Pages: 11

Brand: Gardner Denver Pages: 27

Brand: Sierra Pages: 11

Leslie F-1240LDW

Brand: Circor Pages: 19

Fairbanks nijhuis 2800

Brand: Pentair Pages: 28

Brand: Geotech Pages: 32

Corken Z-Series

Brand: Idex Pages: 32

Brand: T.I.P. Pages: 112

Brand: GE Pages: 24

Brand: Pentair Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands