IWAKI PUMPS EHN-B11-NAE Manual Download

Page: 23 / 68

stal

lat

ion

Plumbing

Plumbing

Connect tubes to the pump and install a check valve.

Before operation

• Cut the tube ends flat.

Necessary tools

• An adjustable wrench or spanner.

Tube connection

a. Pass a tube into the fitting nut and stopper and then slide it down

to the adapter as far as it will go.

b. Put the tube end (adapter) in the fitting. Then hand tighten the

fitting nut.

c. Retighten the fitting nut by turning it further 180 degrees with an

adjustable wrench or spanner (crush tube mount).

Do not use excessive force to the plastic fitting nut.

* In your try to remove the connection, the adapter may be stuck in

the crushed tube and the stopper. Try not to damage the taper of the
adapter that is crushing the tube against the stopper. If it has been dam-
aged, contact us for the new adapter/stopper.

* Do not reuse the same tube end for the crush sealing. Cut it off for

ensuring the new seal is established.

Tube end (side view)

Tube

Fitting nut

Fitting

Stopper

Adapter

Summary of Contents for EHN-B11-NAE





































































Search results

Summary of Contents for EHN-B11-NAE

Reviews:

Related manuals for EHN-B11-NAE

Brands by name

Popular brands

IWAKI PUMPS EHN-B11-NAE, Manual

Search results

Summary of Contents for EHN-B11-NAE

Reviews:

Related manuals for EHN-B11-NAE

Brands by name

Popular brands