Intermec Trakker Antares 2420, User Manual

Page: 468 / 480

TRAKKER Antares 2420 and 2425 Hand-Held Terminal User’s Manual
I-6
communications (continued)
RF specifications, A-5
serial interface module, connecting, 4-12
serial port
configuration commands, list of, 3-28 to 3-29, A-12
connecting, 4-11
troubleshooting, 6-13, 6-15
See also network.
communications dock
charging batteries, 2-27
connecting and using, 4-11
power supply, using, 2-36
terminal accessory, 1-4
upgrading the firmware, using to, 3-21
communications ports, See COM ports
communications protocols
Binary, 4-14
choosing, 4-13
Configurable, 4-14
definition, G-8
Master Polling, 4-15
Polling Mode D, 4-15
computer, See host computer
Configurable protocol, 4-14
Configurable Serial Protocol, defined, 4-36
configuration commands
Acknowledgement Delay Lower Limit, 9-7
Acknowledgement Delay Upper Limit, 9-9
AFF, 9-61
Append Time, 9-10
Automatic Shutoff, 9-11
Baud Rate, 9-13
Beep Volume, 9-15
category, listed by, 9-4
Codabar, 9-16
Code 11, 9-17
Code 128, 9-28
Code 16K, 9-18
Code 2 of 5, 9-19
Code 39, 9-21
Code 49, 9-25
Code 93, 9-27
Command Processing, 9-29 to 9-37
Configuration Commands Via Serial Port, 9-38
configuring
from DCS 300, 4-25
from host, 4-16, 4-26 to 4-30
overview of, 3-3
Controller Connect Check Receive Timer, 9-40
Controller Connect Check Send Timer, 9-41
Controller IP Address, 9-43
Data Bits, 9-45
Decode Security, 9-46
Default Router, 9-47
default settings, list of, A-8 to A-12
definition, G-8
Display Backlight Timeout, 9-49
Display Contrast, 9-50
Display Font Type, 9-51
Display Row Spacing, 9-52
Display Video Mode, 9-53
Dynamic Host Configuration Protocol, 9-54
EOM, 9-55
Flash Memory Configuration, 9-57
Flow Control, 9-58
Handshake, 9-61
Host IP Address, 9-62
Interleaved 2 of 5, 9-64
Keypad Caps Lock, 9-66
Keypad Clicker, 9-66
Keypad Type, 9-67
LRC, 9-68
Maximum Retries, 9-69
Modem Dial Sequence, 9-71
Modem Initialization Sequence, 9-73
MSI, 9-75
Network Activate, 9-76
Network Loopback, 9-77
Network Port, 9-78
Parity, 9-80
Plessey, 9-82
Poll, 9-83
RAM Drive Size, 9-87
recording the configuration, 3-24 to 3-31
Resume Execution, 9-89
RF Domain, 9-90
RF Inactivity Timeout, 9-91
RF Roaming Flag, 9-92
RF Security ID, 9-93
RF Transmit Mode, 9-94
RF Wakeup On Broadcast, 9-95
Scan Ahead, 9-95
Scanner Mode, 9-96
Scanner Redundancy, 9-97
Scanner Selection, 9-98
Scanner Timeout, 9-100
Scanner Trigger, 9-101
scanning labels to configure the terminal, 3-15
Serial Port Protocol, 9-102
SOM, 9-104
Stop Bits, 9-106
Subnet Mask, 9-107
syntax, listed by, A-13
TCP/IP Maximum Transmit Timeout, 9-110
Terminal IP Address, 9-112
Time and Date, 9-114
Time in Seconds, 9-115
Timeout Delay, 9-116
troubleshooting, 6-11, 6-12, 6-13
UPC/EAN, 9-118