manualshive.com logo in svg

Inova Automation NICE1000+, User Manual, Page: 12 / 80

Share
Download
Inova Automation NICE1000+ User Manual Download Page 12

 

 

INOVA AUTOMATION

                         

NICE Series Integrated Elevator Solution 

–

 N Quick Start-Up Guide V1.0               

 

 

12 

 

CN10 

USB 
interface 

Communication 

•• Used to connect the

 

external Bluetooth module for 
commissioning via 
Android cell phone 
(not supporting English version 
currently) 

•• Used to burn the MCB

 program 

•• Used for residential

 

monitoring 

 

CN12 

RJ45 
interface 

Interface for 
operation panel 

Used to connect the 
operation panel 

 

J12 

Interface for connecting the PG card 

 

J9/ 
J10 
 

Factory reserved. Do not short them randomly. Otherwise, the 
controller may not work properly 

 

 

 

2.8.  Description of the MCTC-KZ-D Extension Card 

The extension card is mainly used for extension of floor call button inputs and relay outputs. 

 

2.8.1 Appearance and installation of the MCTC-KZ-D 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
            Actual Appearance of MCTC-KZ-D                                       N connected with MCTC-KZ-D  
 
 
 
 
 

Summary of Contents for NICE1000+

















































































Reviews:

No comments