IBM ThinkPad 380Z User Manual Download Page 28

Page: 28 / 157

Customizing Power Management

This section describes how to customize power management so that
you are using the power management mode appropriate to your
operation.

Setting the Suspend Timer

To set the suspend timer, do the following:

For Windows 98:

Start the ThinkPad Configuration program.

Click on the Power Management (

) button.

The “Power Management Properties” window appears.

Select the Power Schemes tab.

The “Power Schemes” window appears.

Set the length of time for the suspend timer at System
standby timers under Settings for Portable/Laptop power
scheme.

Note:

You can also set the LCD off timers and Hard disk off
timers.

Click on OK.

For Windows 95:

Start the ThinkPad Configuration program.

Click on the Power Management (

) button.

The “Power Properties” window appears.

Select the Power Mode tab.

The “Power Mode” window appears.

Select Customized.

IBM ThinkPad 380Z Online User's Guide

Summary of Contents for ThinkPad 380Z






























































































































































Search results

Summary of Contents for ThinkPad 380Z

Reviews:

Related manuals for ThinkPad 380Z

Brands by name

Popular brands

IBM ThinkPad 380Z, User Manual

Search results

Summary of Contents for ThinkPad 380Z

Reviews:

Related manuals for ThinkPad 380Z

Brands by name

Popular brands