manualshive.com logo in svg

IBM ThinkPad 380Z, User Manual

Share
Download
IBM ThinkPad 380Z User Manual Download Page 20

  Attention 

You should take corrective actions when the battery status
indicator is

 blinking orange, and your computer sounds three

consecutive beeps. (If your computer enters suspend mode
because of a low-battery condition, data in memory might be
lost.)

Immediately connect the AC Adapter to the computer.

Then take either of the following actions:

To continue your work with the AC Adapter, press the Fn

key.

or:

To continue your work with a fully charged battery pack, do

the following:

1. Replace the battery pack with a fully charged one. (See

the 

User's Reference.)

2. Press the Fn key.

3. Disconnect the AC Adapter from the computer.

If you do not take corrective actions within about 30 seconds, the
computer will enter suspend mode.

Do not leave the computer in this condition for an extended
time. Data in memory will be lost.

16

IBM ThinkPad 380Z Online User's Guide 

 

Summary of Contents for ThinkPad 380Z






























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands